А где эта "помойка" ?
А почему бы не составить и поддерживать (и Вам и всем заинтересованным форумцам) ? Разве не полезно было бы ?Сообщение от Hunta
Эта - известна, а еще ?
А где эта "помойка" ?
А почему бы не составить и поддерживать (и Вам и всем заинтересованным форумцам) ? Разве не полезно было бы ?
Эта - известна, а еще ?
С любовью к вам, Yandex.Direct
Размещение рекламы на форуме способствует его дальнейшему развитию
Потому что свободного времени мало и занято оно другим, как правило
Судя по количество запросов с просьбой выложить (конкретику) - нет
Ищущий да обращет
почему так ? Что Вы думаете ?
Меня это не волнует
Даже не знаю, в какую тему засунутьПоэтому сюда
Код:.RUN CFUTIL GETINFO 100:1:161000 TO TT: Getting info... General configuration : 2112 Default number of cylinders : 487 Reserved : 0 Default number of heads : 16 Obsolete : 0 Obsolete : 1100 Default number of sectors per track : 63 Number of sectors per card : 490896 Obsolete : 0 Serial number : STP21240N33 Obsolete : 2 Obsolete : 2 Number of ECC bytes passed on Read/Write Long Commands : 4 Firmware revision : 20130902 Model number : SMART CF Maximum number of sectors on Read/Write Multiple : 100001 Reserved : 0 Capabilities : 7400 Reserved : 0 PIO data transfer cycle timing mode : 1000 Obsolete : 0 Field Validity : 7 Current numbers of cylinders : 487 Current numbers of heads : 16 Current sectors per track : 63 Current capacity in sectors (LBA) : 490896 Multiple sector setting : 400 Total number of sectors addressable in LBA Mode : 490896 Reserved : 0 Multiword DMA transfer : 7 Advanced PIO modes supported : 3 Minimum Multiword DMA transfer cycle time per word : 170 Recommended Multiword DMA transfer cycle time : 170 Minimum PIO transfer cycle time without flow control : 170 Minimum PIO transfer cycle time with IORDY flow control : 170 Reserved : Reserved : Features/command sets supported : Features/command sets enabled : Ultra DMA Mode Supported and Selected : 77 Time required for Security erase unit completion : 0 Time required for Enhanced security erase unit completion: 0 Current Advanced power management value : 0 Reserved : Security status : 0 Vendor unique bytes : Power requirement description : 140040 Reserved for assignment by the CFA : 0 Key management schemes supported : 0 CF Advanced True IDE Timing Mode Capability and Setting : 222 CF Advanced PC Card I/O and Memory Timing Mode Capability: 0 Reserved for assignment by the CFA : Reserved :Табличный парсер, ещё не всё дописано, поэтому не всё и что то не совсем так показывается. Но что то можно использоватьКод:.RUN CFUTIL GETINFO 100:1:161140 TO TT: Getting info... General configuration : 102212 Default number of cylinders : 31045 Reserved : 0 Default number of heads : 16 Obsolete : 0 Obsolete : 0 Default number of sectors per track : 63 Number of sectors per card : 31293360 Obsolete : 0 Serial number : AAZ080619085119 Obsolete : 2 Obsolete : 2 Number of ECC bytes passed on Read/Write Long Commands : 4 Firmware revision : HDX16.01 Model number : SDCFHS-016G Maximum number of sectors on Read/Write Multiple : 100001 Reserved : 0 Capabilities : 7400 Reserved : 0 PIO data transfer cycle timing mode : 1000 Obsolete : 0 Field Validity : 7 Current numbers of cylinders : 31045 Current numbers of heads : 16 Current sectors per track : 63 Current capacity in sectors (LBA) : 31293360 Multiple sector setting : 110400 Total number of sectors addressable in LBA Mode : 31293360 Reserved : 0 Multiword DMA transfer : 7 Advanced PIO modes supported : 3 Minimum Multiword DMA transfer cycle time per word : 170 Recommended Multiword DMA transfer cycle time : 170 Minimum PIO transfer cycle time without flow control : 170 Minimum PIO transfer cycle time with IORDY flow control : 170 Reserved : Reserved : Features/command sets supported : Features/command sets enabled : Ultra DMA Mode Supported and Selected : 377 Time required for Security erase unit completion : 0 Time required for Enhanced security erase unit completion: 0 Current Advanced power management value : 0 Reserved : Security status : 0 Vendor unique bytes : Power requirement description : 100764 Reserved for assignment by the CFA : 0 Key management schemes supported : 0 CF Advanced True IDE Timing Mode Capability and Setting : 222 CF Advanced PC Card I/O and Memory Timing Mode Capability: 0 Reserved for assignment by the CFA : Reserved : .
Расширяю функционал
- - - Добавлено - - -Код:.RUN CFUTIL GETINFO 100:1:161140 TO TT: Getting info... General configuration : 102212 Removable device : X Non-removable device : Default number of cylinders : 31045 Default number of heads : 16 Default number of sectors per track : 63 Number of sectors per card : 31293360 Serial number : AAZ080619085119 Number of ECC bytes passed on Read/Write Long Commands : 4 Firmware revision : HDX16.01 Model number : SDCFHS-016G Maximum number of sectors on Read/Write Multiple : 100001 Capabilities : 7400 Standby Timer supported : IORDY supported : X IORDY may be disabled : X LBA supported : X DMA supported : X PIO data transfer cycle timing mode : 2 Translation Parameters Valid : 7 Curr num of cyls, heads, sectors and capacity valid : X Adv PIO modes, MW DMA and Min PIO xfrr cycle valid : X Ultra DMA Modes valid : X Current numbers of cylinders : 31045 Current numbers of heads : 16 Current sectors per track : 63 Current capacity in sectors (LBA) : 31293360 Multiple sector setting : 0 Multiple sector setting valid : X Total number of sectors addressable in LBA Mode : 31293360 Multiword DMA transfer : 7 Multiword DMA mode 0 supported : X Multiword DMA mode 1 supported : X Multiword DMA mode 2 supported : X Multiword DMA mode 0 selected : Multiword DMA mode 1 selected : Multiword DMA mode 2 selected : Advanced PIO modes supported : 3 PIO mode 3 supported : X PIO mode 4 supported : X PIO mode 3 selected : PIO mode 4 selected : Minimum Multiword DMA transfer cycle time per word, ns : 170 Recommended Multiword DMA transfer cycle time, ns : 170 Minimum PIO transfer cycle time without flow control, ns : 170 Minimum PIO transfer cycle time with IORDY flow control, ns: 170 Features/command sets supported : SMART feature set is supported : X Security Mode feature set is supported : Removable Media feature set is supported : Power Management feature set is supported : X Packet Command feature set is supported : Write cache is supported : X Look-ahead is supported : Release interrupt is supported : Service interrupt is supported : Device Reset command is supported : Host Protected Area feature set is supported : Write Buffer command is supported : X Read Buffer command is supported : X NOP command is supported : X Download Microcode command is supported : Read/Write DMA Queued commands is supported : CFA feature set command is supported : X Advanced Power Management feature set is supported : X Removable Media Status feature set is supported : Features/command sets enabled : SMART feature set has been enabled : Security Mode feature set has been enabled : Removable Media feature set has been enabled : Power Management feature set has been enabled : Packet Command feature set has been enabled : Write cache has been enabled : Look-ahead has been enabled : Release interrupt has been enabled : Service interrupt has been enabled : Device Reset command has been enabled : Host Protected Area feature set has been enabled : Write Buffer command has been enabled : Read Buffer command has been enabled : NOP command has been enabled : Download Microcode command has been enabled : Read/Write DMA Queued commands has been enabled : CFA feature set command has been enabled : Advanced Power Management feature set has been enabled : Removable Media Status feature set has been enabled : Ultra DMA Mode Supported and Selected : 377 Time required for Security erase unit completion : 0 Time required for Enhanced security erase unit completion : 0 Current Advanced power management value : 0 Security status : 0 Vendor unique bytes : Power requirement description : 100764 Reserved for assignment by the CFA : 0 Key management schemes supported : 0 CF Advanced True IDE Timing Mode Capability and Setting : 222 CF Advanced PC Card I/O and Memory Timing Mode Capability : 0 .
Как выглядит описание, по которому идёт расшифровка
Код:CF$DSC 0, 2, D$W, , <General configuration> CF$DSC 0, 2, D$BIT, 7. , <Removable device> CF$DSC 0, 2, D$BIT, 6. , <Non-removable device> CF$DSC 1, 2, D$W10, , <Default number of cylinders> ; CF$DSC 2, 2, D$W, , <Reserved> CF$DSC 3, 2, D$W10, , <Default number of heads> ; CF$DSC 4, 2, D$W, , <Obsolete> ; CF$DSC 5, 2, D$W, , <Obsolete> CF$DSC 6, 2, D$W10, , <Default number of sectors per track> CF$DSC 7, 4, D$DE10, , <Number of sectors per card> ; CF$DSC 9, 2, D$W, , <Obsolete> CF$DSC 10, 20, D$STR, , <Serial number> ; CF$DSC 20, 2, D$W, , <Obsolete> ; CF$DSC 21, 2, D$W, , <Obsolete> CF$DSC 22, 2, D$W, , <Number of ECC bytes passed on Read/Write Long Commands> CF$DSC 23, 8, D$STR, , <Firmware revision> CF$DSC 27, 40, D$STR, , <Model number> CF$DSC 47, 2, D$W, , <Maximum number of sectors on Read/Write Multiple> ; CF$DSC 48, 2, D$W, , <Reserved> CF$DSC 49, 2, D$W, , <Capabilities> CF$DSC 49, 2, D$BIT, 13. , <Standby Timer supported> CF$DSC 49, 2, D$BIT, 11. , <IORDY supported> CF$DSC 49, 2, D$BIT, 10. , <IORDY may be disabled> CF$DSC 49, 2, D$BIT, 9. , <LBA supported> CF$DSC 49, 2, D$BIT, 8. , <DMA supported> ; CF$DSC 50, 2, D$W, , <Reserved> CF$DSC 51, 2, D$HB, , <PIO data transfer cycle timing mode> ; CF$DSC 52, 2, D$W, , <Obsolete> CF$DSC 53, 2, D$W, , <Translation Parameters Valid> CF$DSC 53, 2, D$BIT, 0. , <Curr num of cyls, heads, sectors and capacity valid> CF$DSC 53, 2, D$BIT, 1. , <Adv PIO modes, MW DMA and Min PIO xfrr cycle valid> CF$DSC 53, 2, D$BIT, 2. , <Ultra DMA Modes valid> CF$DSC 54, 2, D$W10, , <Current numbers of cylinders> CF$DSC 55, 2, D$W10, , <Current numbers of heads> CF$DSC 56, 2, D$W10, , <Current sectors per track> CF$DSC 57, 4, D$DW10, , <Current capacity in sectors (LBA)> CF$DSC 59, 2, D$LB, , <Multiple sector setting> CF$DSC 59, 2, D$BIT, 8. , <Multiple sector setting valid> CF$DSC 60, 4, D$DW10, , <Total number of sectors addressable in LBA Mode> ; CF$DSC 62, 2, D$W, , <Reserved> CF$DSC 63, 2, D$W, , <Multiword DMA transfer> CF$DSC 63, 2, D$BIT, 0. , <Multiword DMA mode 0 supported> CF$DSC 63, 2, D$BIT, 1. , <Multiword DMA mode 1 supported> CF$DSC 63, 2, D$BIT, 2. , <Multiword DMA mode 2 supported> CF$DSC 63, 2, D$BIT, 8. , <Multiword DMA mode 0 selected> CF$DSC 63, 2, D$BIT, 9. , <Multiword DMA mode 1 selected> CF$DSC 63, 2, D$BIT, 10. , <Multiword DMA mode 2 selected> CF$DSC 64, 2, D$W, , <Advanced PIO modes supported> CF$DSC 64, 2, D$BIT, 0. , <PIO mode 3 supported> CF$DSC 64, 2, D$BIT, 1. , <PIO mode 4 supported> CF$DSC 64, 2, D$BIT, 8. , <PIO mode 3 selected> CF$DSC 64, 2, D$BIT, 9. , <PIO mode 4 selected> CF$DSC 65, 2, D$W, , <Minimum Multiword DMA transfer cycle time per word, ns> CF$DSC 66, 2, D$W, , <Recommended Multiword DMA transfer cycle time, ns> CF$DSC 67, 2, D$W, , <Minimum PIO transfer cycle time without flow control, ns> CF$DSC 68, 2, D$W, , <Minimum PIO transfer cycle time with IORDY flow control, ns> ; CF$DSC 69, 20, D$NOSHOW, , <Reserved> ; CF$DSC 80, 4, D$DW, , <Reserved> CF$DSC 82, 6, D$PROC, DPROC1, <Features/command sets supported> CF$DSC 82, 2, D$BIT, 0. , <SMART feature set is supported> CF$DSC 82, 2, D$BIT, 1. , <Security Mode feature set is supported> CF$DSC 82, 2, D$BIT, 2. , <Removable Media feature set is supported> CF$DSC 82, 2, D$BIT, 3. , <Power Management feature set is supported> CF$DSC 82, 2, D$BIT, 4. , <Packet Command feature set is supported> CF$DSC 82, 2, D$BIT, 5. , <Write cache is supported> CF$DSC 82, 2, D$BIT, 6. , <Look-ahead is supported> CF$DSC 82, 2, D$BIT, 7. , <Release interrupt is supported> CF$DSC 82, 2, D$BIT, 8. , <Service interrupt is supported> CF$DSC 82, 2, D$BIT, 9. , <Device Reset command is supported> CF$DSC 82, 2, D$BIT, 10. , <Host Protected Area feature set is supported> ; CF$DSC 82, 2, D$BIT, 11. , <Obsolete> CF$DSC 82, 2, D$BIT, 12. , <Write Buffer command is supported> CF$DSC 82, 2, D$BIT, 13. , <Read Buffer command is supported> CF$DSC 82, 2, D$BIT, 14. , <NOP command is supported> ; CF$DSC 82, 2, D$BIT, 15. , <Obsolete> CF$DSC 82, 2, D$BIT, 16. , <Download Microcode command is supported> CF$DSC 82, 2, D$BIT, 17. , <Read/Write DMA Queued commands is supported> CF$DSC 82, 2, D$BIT, 18. , <CFA feature set command is supported> CF$DSC 82, 2, D$BIT, 19. , <Advanced Power Management feature set is supported> CF$DSC 82, 2, D$BIT, 20. , <Removable Media Status feature set is supported> CF$DSC 85, 6, D$PROC, DPROC2, <Features/command sets enabled> CF$DSC 85, 2, D$BIT, 0. , <SMART feature set has been enabled> CF$DSC 85, 2, D$BIT, 1. , <Security Mode feature set has been enabled> CF$DSC 85, 2, D$BIT, 2. , <Removable Media feature set has been enabled> CF$DSC 85, 2, D$BIT, 3. , <Power Management feature set has been enabled> CF$DSC 85, 2, D$BIT, 4. , <Packet Command feature set has been enabled> CF$DSC 85, 2, D$BIT, 5. , <Write cache has been enabled> CF$DSC 85, 2, D$BIT, 6. , <Look-ahead has been enabled> CF$DSC 85, 2, D$BIT, 7. , <Release interrupt has been enabled> CF$DSC 85, 2, D$BIT, 8. , <Service interrupt has been enabled> CF$DSC 85, 2, D$BIT, 9. , <Device Reset command has been enabled> CF$DSC 85, 2, D$BIT, 10. , <Host Protected Area feature set has been enabled> ; CF$DSC 85, 2, D$BIT, 11. , <Obsolete> CF$DSC 85, 2, D$BIT, 12. , <Write Buffer command has been enabled> CF$DSC 85, 2, D$BIT, 13. , <Read Buffer command has been enabled> CF$DSC 85, 2, D$BIT, 14. , <NOP command has been enabled> ; CF$DSC 85, 2, D$BIT, 15. , <Obsolete> CF$DSC 85, 2, D$BIT, 16. , <Download Microcode command has been enabled> CF$DSC 85, 2, D$BIT, 17. , <Read/Write DMA Queued commands has been enabled> CF$DSC 85, 2, D$BIT, 18. , <CFA feature set command has been enabled> CF$DSC 85, 2, D$BIT, 19. , <Advanced Power Management feature set has been enabled> CF$DSC 85, 2, D$BIT, 20. , <Removable Media Status feature set has been enabled> CF$DSC 88, 2, D$W, , <Ultra DMA Mode Supported and Selected> CF$DSC 89, 2, D$W, , <Time required for Security erase unit completion> CF$DSC 90, 2, D$W, , <Time required for Enhanced security erase unit completion> CF$DSC 91, 2, D$W, , <Current Advanced power management value> ; CF$DSC 92, 72, D$NOSHOW, , <Reserved> CF$DSC 128, 2, D$W, , <Security status> CF$DSC 129, 64, D$BS, , <Vendor unique bytes> CF$DSC 160, 2, D$W, , <Power requirement description> CF$DSC 161, 2, D$W, , <Reserved for assignment by the CFA> CF$DSC 162, 2, D$W, , <Key management schemes supported> CF$DSC 163, 2, D$W, , <CF Advanced True IDE Timing Mode Capability and Setting> CF$DSC 164, 2, D$W, , <CF Advanced PC Card I/O and Memory Timing Mode Capability> ; CF$DSC 165, 6, D$BS, , <Reserved for assignment by the CFA> ; CF$DSC 168, 158, D$NOSHOW, , <Reserved> CF$DSC , , D$END
Руки добрались до RQDX3. Для соединения с платой расширения использовал кабель, который на microvax-ах используется для соединение платы процессора и плат памяти - IDE50, прямое соединение контактов между разъёмами - что ещё нужно для соединения плат
Под раздачу попал Seagate ST-124 - 615x4x17 - примерно 20 мб. Форматирование и тестирования программой ZRQC прошло успешно. Сейчас идёт копирование системы.
В системе уже стоит плата CMD-420 как основной контроллер DU, так что для этой переставил CSR на альтернативный адрес.
- - - Добавлено - - -
К сожалению, загрузка не идёт ни в каком виде. Попробую поставить CSR на стандартный и загрузитьсяКод:Commands are Help, Boot, List, Setup, Map and Test. Type a command then press the RETURN key: BOO DU0 Trying DU0 Starting system from DU0 BOOTING UP XXDP-XM EXTENDED MONITOR XXDP-XM EXTENDED MONITOR - XXDP V2.5 REVISION: F0 BOOTED FROM DU0 124KW OF MEMORY NON-UNIBUS SYSTEM RESTART ADDRESS: 152000 TYPE "H" FOR HELP ! .R ZRQC?? ZRQCF0.BIN DRSSM-G2 ZRQC-F-0 RQDX3 Disk Formatter Utility UNIT IS Formattable Winchester (RDnn) or Floppy (RX33) Drives RSTRT ADR 145702 DR>START CHANGE HW (L) ? Y # UNITS (D) ? 1 UNIT 0 Enter controller IP Address (O) 172150 ? 172160 Do you want to use the "AUTOFORMAT" Mode [Y/N] (L) Y ? N **** WARNING **** ALL DATA ON SELECTED DRIVE WILL BE DESTROYED Write protect all drives not being formatted. Please verify that the selected drive is ON LINE and NOT write protected. If formatting RX33 media, insert media to be formatted in the selected drive. Do you wish to continue [Y/N] (L) N ? Y MSCP Controller Model: 19 Microcode Version: 4 What unit do you want to format [0-255] (A) ? 0 Do you want to use manufacturing bad block information [Y/N] (A) N ? Downline load UIT [Y/N] (A) Y ? UIT Drive Name _______________________________________________________ 0 RD51 1 RD52 part # 30-21721-02 (1 light on front panel) 2 RD52 part # 30-23227-02 (2 lights on front panel) 3 RD53 4 RD31 5 RD54 6 RD32 Enter Unit Identifier Table (UIT) [0-6] (D) ? 4 Continue if bad block information is inaccessible [Y/N] (A) N ? Y Please type in the serial number [8-10 digits] (A) ? 1234567890 Formatting of Drive 0 Begun -- Total number of LBN's to format is 41584. ------------ FORMAT PROGRESS REPORT ------------- 1 minute into format ---- Formatting tracks, LBN # 32675 2 minutes into format ---- First check pass, writing LBN # 34867 3 minutes into format ---- First check pass, reading LBN # 9064 4 minutes into format ---- First check pass, reading LBN # 40715 5 minutes into format ---- Second check pass, writing LBN # 35003 6 minutes into format ---- Second check pass, reading LBN # 28271 8 minutes into format ---- Third check pass, writing LBN # 35003 9 minutes into format ---- Third check pass, reading LBN # 28271 Format Completed. 00002 Rev LBNs 00000 Bad RBNs 00000 Bad DBNs 00000 Bad XBNs 00002 retired FCT was not used. Drive 0 has been formatted successfully. ZRQC EOP 1 0 TOTAL ERRS DR> 150230 @1777773000G# Testing in progress - Please wait Memory Size is 4088 K Bytes 9 Step memory test Step 1 2 3 4 5 6 7 8 9 Message 04 Entering Dialog mode Commands are Help, Boot, List, Setup, Map and Test. Type a command then press the RETURN key: BOO ZB1 Trying ZB1 Starting system from ZB1 RT-11SB (S) V05.07 .R MSCPCK .SET DU CSR 172160 .DUMP/TERM/END:1 DU: DU: BLOCK NUMBER 000000 000/ 000004 000010 000020 000040 000100 000200 000400 001000 *...... .@.......* 020/ 002000 004000 010000 020000 040000 100001 000002 000004 *....... .@......* 040/ 000010 000020 000040 000100 000200 000400 001000 002000 *.... .@.........* 060/ 004000 010000 020000 040000 100001 000002 000004 000010 *..... .@........* 100/ 000020 000040 000100 000200 000400 001000 002000 004000 *.. .@...........* 120/ 010000 020000 040000 100001 000002 000004 000010 000020 *... .@..........* 140/ 000040 000100 000200 000400 001000 002000 004000 010000 * .@.............* 160/ 020000 040000 100001 000002 000004 000010 000020 000040 *. .@.......... .* 200/ 000100 000200 000400 001000 002000 004000 010000 020000 *@.............. * 220/ 040000 100001 000002 000004 000010 000020 000040 000100 *.@.......... .@.* ....... .INI DU: DU0:/Initialize; Are you sure? Y Volume contains protected files; Are you sure? N .DIR DU: AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD- ... .INI DU: DU0:/Initialize; Are you sure? Y Volume contains protected files; Are you sure? Y .DIR DU: 0 Files, 0 Blocks 41492 Free blocks .DAT 10-MAR-2021 .TIM 13:36 .TIM 13:36:45 .COP/SYS/VER SY:*.* DU: Files copied: SY:SWAP.SYS to DU:SWAP.SYS SY:RT11SB.SYS to DU:RT11SB.SYS SY:RT11FB.SYS to DU:RT11FB.SYS SY:RK.SYS to DU:RK.SYS SY:DL.SYS to DU:DL.SYS SY:DU.SYS to DU:DU.SYS SY:HX.SYS to DU:HX.SYS SY:ZA.SYS to DU:ZA.SYS SY:ZB.SYS to DU:ZB.SYS SY:ZC.SYS to DU:ZC.SYS SY:ZD.SYS to DU:ZD.SYS SY:ZE.SYS to DU:ZE.SYS SY:ZF.SYS to DU:ZF.SYS SY:WQ.SYS to DU:WQ.SYS SY:WS.SYS to DU:WS.SYS SY:LD.SYS to DU:LD.SYS SY:VM.SYS to DU:VM.SYS SY:MU.SYS to DU:MU.SYS SY:NL.SYS to DU:NL.SYS SY:SL.SYS to DU:SL.SYS SY:RT11XM.SYS to DU:RT11XM.SYS SY:RT11XB.SYS to DU:RT11XB.SYS SY:RT11ZM.SYS to DU:RT11ZM.SYS SY:RT11ZB.SYS to DU:RT11ZB.SYS SY:RKX.SYS to DU:RKX.SYS SY:DLX.SYS to DU:DLX.SYS SY:DUX.SYS to DU:DUX.SYS SY:HXX.SYS to DU:HXX.SYS SY:ZAX.SYS to DU:ZAX.SYS SY:ZBX.SYS to DU:ZBX.SYS SY:ZCX.SYS to DU:ZCX.SYS SY:ZDX.SYS to DU:ZDX.SYS SY:ZEX.SYS to DU:ZEX.SYS SY:ZFX.SYS to DU:ZFX.SYS SY:WQX.SYS to DU:WQX.SYS SY:WSX.SYS to DU:WSX.SYS SY:LDX.SYS to DU:LDX.SYS SY:VMX.SYS to DU:VMX.SYS SY:MUX.SYS to DU:MUX.SYS SY:NLX.SYS to DU:NLX.SYS SY:SLX.SYS to DU:SLX.SYS SY:NQX.SYS to DU:NQX.SYS SY:PIP.SAV to DU:PIP.SAV SY:DUP.SAV to DU:DUP.SAV SY:DIR.SAV to DU:DIR.SAV SY:IND.SAV to DU:IND.SAV SY:RESORC.SAV to DU:RESORC.SAV SY:EDIT.SAV to DU:EDIT.SAV SY:KED.SAV to DU:KED.SAV SY:KEX.SAV to DU:KEX.SAV SY:MACRO.SAV to DU:MACRO.SAV SY:CREF.SAV to DU:CREF.SAV SY:LINK.SAV to DU:LINK.SAV SY:MONMRG.SAV to DU:MONMRG.SAV SY:LIBR.SAV to DU:LIBR.SAV SY:FILEX.SAV to DU:FILEX.SAV SY:SRCCOM.SAV to DU:SRCCOM.SAV SY:BINCOM.SAV to DU:BINCOM.SAV SY:SLP.SAV to DU:SLP.SAV SY:DUMP.SAV to DU:DUMP.SAV SY:SIPP.SAV to DU:SIPP.SAV SY:BUP.SAV to DU:BUP.SAV SY:PAT.SAV to DU:PAT.SAV SY:HELP.SAV to DU:HELP.SAV SY:SYSMAC.SML to DU:SYSMAC.SML SY:SYSLIB.OBJ to DU:SYSLIB.OBJ SY:FORMAT.SAV to DU:FORMAT.SAV SY:SETUP.SAV to DU:SETUP.SAV SY:VTCOM.SAV to DU:VTCOM.SAV SY:DATIME.SAV to DU:DATIME.SAV SY:DATIME.MAC to DU:DATIME.MAC SY:DATIME.COM to DU:DATIME.COM SY:LET.SAV to DU:LET.SAV SY:SPLIT.SAV to DU:SPLIT.SAV SY:UCL.SAV to DU:UCL.SAV SY:VBGEXE.SAV to DU:VBGEXE.SAV SY:TERMID.SAV to DU:TERMID.SAV SY:TRANSF.SAV to DU:TRANSF.SAV SY:TRANSF.TSK to DU:TRANSF.TSK SY:TRANSF.EXE to DU:TRANSF.EXE SY:ODT.OBJ to DU:ODT.OBJ SY:VDT.OBJ to DU:VDT.OBJ SY:MDUP.SAV to DU:MDUP.SAV SY:MBOOT.BOT to DU:MBOOT.BOT SY:MBOT16.BOT to DU:MBOT16.BOT SY:MSBOOT.BOT to DU:MSBOOT.BOT SY:MDUP.AI to DU:MDUP.AI SY:MDUP.MM to DU:MDUP.MM SY:MDUP.MS to DU:MDUP.MS SY:MDUP.MT to DU:MDUP.MT SY:MDUP.MU to DU:MDUP.MU SY:VERIFY.COM to DU:VERIFY.COM SY:IVP.COM to DU:IVP.COM SY:IVP.MAC to DU:IVP.MAC SY:MTB.COM to DU:MTB.COM SY:MSB.COM to DU:MSB.COM SY:MUB.COM to DU:MUB.COM SY:SB.MAC to DU:SB.MAC SY:FB.MAC to DU:FB.MAC SY:XM.MAC to DU:XM.MAC SY:XB.MAC to DU:XB.MAC SY:ZM.MAC to DU:ZM.MAC SY:ZB.MAC to DU:ZB.MAC SY:SYSTEM.MLB to DU:SYSTEM.MLB SY:EDTL.MLB to DU:EDTL.MLB SY:SYSGEN.COM to DU:SYSGEN.COM SY:CONFIG.COM to DU:CONFIG.COM SY:CONFIG.SAV to DU:CONFIG.SAV SY:V5USER.TXT to DU:V5USER.TXT SY:V5NOTE.TXT to DU:V5NOTE.TXT SY:CUSTOM.TXT to DU:CUSTOM.TXT SY:MSCPCK.SAV to DU:MSCPCK.SAV SY:DBGSYM.SAV to DU:DBGSYM.SAV SY:INDEX.SAV to DU:INDEX.SAV SY:INDEXX.SAV to DU:INDEXX.SAV SY:INDEXA.IMG to DU:INDEXA.IMG SY:INDEXB.IMG to DU:INDEXB.IMG SY:INDEX.IDX to DU:INDEX.IDX SY:TECO.SAV to DU:TECO.SAV SY:SGN02.CND to DU:SGN02.CND SY:SGN02.ANS to DU:SGN02.ANS SY:SGN02.BLD to DU:SGN02.BLD SY:SGN02.MON to DU:SGN02.MON SY:SGN02.DEV to DU:SGN02.DEV SY:SGN02.TBL to DU:SGN02.TBL SY:RT11SB.MAP to DU:RT11SB.MAP SY:RT11FB.MAP to DU:RT11FB.MAP SY:RT11XM.MAP to DU:RT11XM.MAP SY:RT11XB.MAP to DU:RT11XB.MAP SY:RT11ZM.MAP to DU:RT11ZM.MAP SY:RT11ZB.MAP to DU:RT11ZB.MAP SY:STRTSB.COM to DU:STRTSB.COM SY:STRTFB.COM to DU:STRTFB.COM SY:STRTXM.COM to DU:STRTXM.COM SY:STRTXB.COM to DU:STRTXB.COM SY:STRTZM.COM to DU:STRTZM.COM SY:STRTZB.COM to DU:STRTZB.COM SY:HELAY.SYS to DU:HELAY.SYS SY:EM.SYS to DU:EM.SYS SY:TSYB10.COM to DU:TSYB10.COM SY:TSYNL.COM to DU:TSYNL.COM .TIM 13:47:47 .DIR DU: 10-Mar-2021 SWAP .SYS 28P 31-Oct-1998 RT11SB.SYS 99P 02-Oct-2020 RT11FB.SYS 107P 02-Oct-2020 RK .SYS 3P 02-Oct-2020 DL .SYS 5P 02-Oct-2020 DU .SYS 24P 02-Oct-2020 HX .SYS 6P 12-Sep-2020 ZA .SYS 4P 05-Jul-2020 ZB .SYS 4P 05-Jul-2020 ZC .SYS 4P 05-Jul-2020 ZD .SYS 4P 05-Jul-2020 ZE .SYS 4P 05-Jul-2020 ZF .SYS 4P 05-Jul-2020 WQ .SYS 4P 05-Jul-2020 WS .SYS 4P 05-Jul-2020 LD .SYS 11P 02-Oct-2020 VM .SYS 3P 02-Oct-2020 MU .SYS 14P 02-Oct-2020 NL .SYS 2P 02-Oct-2020 SL .SYS 17P 31-Oct-1998 RT11XM.SYS 124P 02-Oct-2020 RT11XB.SYS 115P 02-Oct-2020 RT11ZM.SYS 127P 02-Oct-2020 RT11ZB.SYS 118P 02-Oct-2020 RKX .SYS 3P 02-Oct-2020 DLX .SYS 5P 02-Oct-2020 DUX .SYS 27P 02-Oct-2020 HXX .SYS 6P 12-Sep-2020 ZAX .SYS 4P 05-Jul-2020 ZBX .SYS 4P 05-Jul-2020 ZCX .SYS 4P 05-Jul-2020 ZDX .SYS 4P 05-Jul-2020 ZEX .SYS 4P 05-Jul-2020 ZFX .SYS 4P 05-Jul-2020 WQX .SYS 4P 05-Jul-2020 WSX .SYS 4P 05-Jul-2020 LDX .SYS 11P 02-Oct-2020 VMX .SYS 3P 02-Oct-2020 MUX .SYS 19P 02-Oct-2020 NLX .SYS 2P 02-Oct-2020 SLX .SYS 20P 31-Oct-1998 NQX .SYS 10P 02-Oct-2020 PIP .SAV 30P 31-Oct-1998 DUP .SAV 52P 31-Oct-1998 DIR .SAV 20P 31-Oct-1998 IND .SAV 58P 31-Oct-1998 RESORC.SAV 35P 31-Oct-1998 EDIT .SAV 19P 31-Oct-1998 KED .SAV 85P 31-Oct-1998 KEX .SAV 72P 31-Oct-1998 MACRO .SAV 63P 31-Oct-1998 CREF .SAV 6P 31-Oct-1998 LINK .SAV 59P 31-Oct-1998 MONMRG.SAV 14P 31-Oct-1998 LIBR .SAV 24P 31-Oct-1998 FILEX .SAV 22P 31-Oct-1998 SRCCOM.SAV 26P 31-Oct-1998 BINCOM.SAV 25P 31-Oct-1998 SLP .SAV 13P 31-Oct-1998 DUMP .SAV 10P 31-Oct-1998 SIPP .SAV 21P 31-Oct-1998 BUP .SAV 68P 31-Oct-1998 PAT .SAV 11P 31-Oct-1998 HELP .SAV 161P 31-Oct-1998 SYSMAC.SML 92P 31-Oct-1998 SYSLIB.OBJ 84P 31-Oct-1998 FORMAT.SAV 28P 31-Oct-1998 SETUP .SAV 43P 31-Oct-1998 VTCOM .SAV 24P 31-Oct-1998 DATIME.SAV 4P 31-Oct-1998 DATIME.MAC 23P 31-Oct-1998 DATIME.COM 3P 31-Oct-1998 LET .SAV 6P 31-Oct-1998 SPLIT .SAV 3P 31-Oct-1998 UCL .SAV 16P 31-Oct-1998 VBGEXE.SAV 18P 31-Oct-1998 TERMID.SAV 4P 31-Oct-1998 TRANSF.SAV 16P 31-Oct-1998 TRANSF.TSK 76P 31-Oct-1998 TRANSF.EXE 45P 31-Oct-1998 ODT .OBJ 8P 31-Oct-1998 VDT .OBJ 8P 31-Oct-1998 MDUP .SAV 22P 31-Oct-1998 MBOOT .BOT 1P 31-Oct-1998 MBOT16.BOT 1P 31-Oct-1998 MSBOOT.BOT 4P 31-Oct-1998 MDUP .AI 72P 31-Oct-1998 MDUP .MM 72P 31-Oct-1998 MDUP .MS 72P 31-Oct-1998 MDUP .MT 72P 31-Oct-1998 MDUP .MU 72P 31-Oct-1998 VERIFY.COM 2P 31-Oct-1998 IVP .COM 16P 31-Oct-1998 IVP .MAC 33P 31-Oct-1998 MTB .COM 16P 31-Oct-1998 MSB .COM 16P 31-Oct-1998 MUB .COM 16P 31-Oct-1998 SB .MAC 1P 31-Oct-1998 FB .MAC 1P 31-Oct-1998 XM .MAC 1P 31-Oct-1998 XB .MAC 1P 31-Oct-1998 ZM .MAC 1P 31-Oct-1998 ZB .MAC 1P 31-Oct-1998 SYSTEM.MLB 148P 31-Oct-1998 EDTL .MLB 11P 31-Oct-1998 SYSGEN.COM 286P 31-Oct-1998 CONFIG.COM 29P 31-Oct-1998 CONFIG.SAV 10P 31-Oct-1998 V5USER.TXT 2P 31-Oct-1998 V5NOTE.TXT 36P 31-Oct-1998 CUSTOM.TXT 14P 31-Oct-1998 MSCPCK.SAV 4P 31-Oct-1998 DBGSYM.SAV 10P 31-Oct-1998 INDEX .SAV 11P 31-Oct-1998 INDEXX.SAV 14P 31-Oct-1998 INDEXA.IMG 164P 31-Oct-1998 INDEXB.IMG 165P 31-Oct-1998 INDEX .IDX 7P 31-Oct-1998 TECO .SAV 50P 31-Oct-1998 SGN02 .CND 5P 02-Oct-2020 SGN02 .ANS 9P 02-Oct-2020 SGN02 .BLD 3P 02-Oct-2020 SGN02 .MON 10P 02-Oct-2020 SGN02 .DEV 6P 02-Oct-2020 SGN02 .TBL 5P 02-Oct-2020 RT11SB.MAP 34P 02-Oct-2020 RT11FB.MAP 35P 02-Oct-2020 RT11XM.MAP 38P 02-Oct-2020 RT11XB.MAP 36P 02-Oct-2020 RT11ZM.MAP 38P 02-Oct-2020 RT11ZB.MAP 36P 02-Oct-2020 STRTSB.COM 1P 31-Oct-1998 STRTFB.COM 5P 31-Oct-1998 STRTXM.COM 8P 31-Oct-1998 STRTXB.COM 5P 31-Oct-1998 STRTZM.COM 8P 31-Oct-1998 STRTZB.COM 5P 31-Oct-1998 HELAY .SYS 1 13-Jun-1988 EM .SYS 4 04-Mar-2012 TSYB10.COM 1 16-Oct-2020 TSYNL .COM 1 16-Oct-2020 141 Files, 4116 Blocks 37376 Free blocks .COP/BOO DU:RT11ZM DU: .BOO DU: 000002 @
- - - Добавлено - - -
Предположение о том, что проблема связана с нестандартным адресом подтвердилось
41560 блоков - итого скорость 236 кб/сКод:Testing in progress - Please wait Memory Size is 4088 K Bytes 9 Step memory test Step 1 2 3 4 5 6 7 8 9 Message 04 Entering Dialog mode Commands are Help, Boot, List, Setup, Map and Test. Type a command then press the RETURN key: BOO DU0 Trying DU0 Starting system from DU0 RT-11ZM (S) V05.07 .TYPE V5USER.TXT RT-11 V5.7 Installation of RT-11 Version 5.7 is complete and you are now running RT-11 from your system volume. Your system volume is your working volume if you have used the Automatic Installation (AI) procedure. If you have installed RT-11 using that procedure, Mentec recommends you verify the correct operation of your system's software using the VERIFY verification procedure. You can only perform VERIFY on the valid target (output) media you used for the AI procedure. Run VERIFY before you run CONFIG. To run VERIFY, enter the command: IND VERIFY You should read the file V5NOTE.TXT, which you can TYPE or PRINT. Also, read the Introduction to RT-11, and the Installation Guide which contain much of the information you need to use RT-11 Version 5.7. .R MSCPCK .SHO DEV Device Status CSR Vector(s) ------ ------ --- --------- RK Installed 177400 220 DL Not installed 174400 160 DU Resident 172150 154 HX Installed 177560 000 ZA Installed 161014 350 ZB Installed 161054 354 ZC Installed 161114 360 ZD Installed 161154 364 ZE Not installed 161214 370 ZF Not installed 161254 374 WQ Not installed 177134 204 WS Not installed 177134 204 LD Installed 000000 000 VM Installed 177572 000 MU Not installed 174500 260 NL Installed 000000 000 SL Installed 000000 000 NQ Installed 174440 120 .DIR SWAP .SYS 28P 31-Oct-1998 RT11SB.SYS 99P 02-Oct-2020 RT11FB.SYS 107P 02-Oct-2020 RK .SYS 3P 02-Oct-2020 DL .SYS 5P 02-Oct-2020 DU .SYS 24P 02-Oct-2020 HX .SYS 6P 12-Sep-2020 ZA .SYS 4P 05-Jul-2020 ZB .SYS 4P 05-Jul-2020 ZC .SYS 4P 05-Jul-2020 ZD .SYS 4P 05-Jul-2020 ZE .SYS 4P 05-Jul-2020 ZF .SYS 4P 05-Jul-2020 WQ .SYS 4P 05-Jul-2020 WS .SYS 4P 05-Jul-2020 LD .SYS 11P 02-Oct-2020 VM .SYS 3P 02-Oct-2020 MU .SYS 14P 02-Oct-2020 NL .SYS 2P 02-Oct-2020 SL .SYS 17P 31-Oct-1998 RT11XM.SYS 124P 02-Oct-2020 RT11XB.SYS 115P 02-Oct-2020 RT11ZM.SYS 127P 02-Oct-2020 RT11ZB.SYS 118P 02-Oct-2020 RKX .SYS 3P 02-Oct-2020 DLX .SYS 5P 02-Oct-2020 DUX .SYS 27P 02-Oct-2020 HXX .SYS 6P 12-Sep-2020 ZAX .SYS 4P 05-Jul-2020 ZBX .SYS 4P 05-Jul-2020 ZCX .SYS 4P 05-Jul-2020 ZDX .SYS 4P 05-Jul-2020 ZEX .SYS 4P 05-Jul-2020 ZFX .SYS 4P 05-Jul-2020 WQX .SYS 4P 05-Jul-2020 WSX .SYS 4P 05-Jul-2020 LDX .SYS 11P 02-Oct-2020 VMX .SYS 3P 02-Oct-2020 MUX .SYS 19P 02-Oct-2020 NLX .SYS 2P 02-Oct-2020 SLX .SYS 20P 31-Oct-1998 NQX .SYS 10P 02-Oct-2020 PIP .SAV 30P 31-Oct-1998 DUP .SAV 52P 31-Oct-1998 DIR .SAV 20P 31-Oct-1998 IND .SAV 58P 31-Oct-1998 RESORC.SAV 35P 31-Oct-1998 EDIT .SAV 19P 31-Oct-1998 KED .SAV 85P 31-Oct-1998 KEX .SAV 72P 31-Oct-1998 MACRO .SAV 63P 31-Oct-1998 CREF .SAV 6P 31-Oct-1998 LINK .SAV 59P 31-Oct-1998 MONMRG.SAV 14P 31-Oct-1998 LIBR .SAV 24P 31-Oct-1998 FILEX .SAV 22P 31-Oct-1998 SRCCOM.SAV 26P 31-Oct-1998 BINCOM.SAV 25P 31-Oct-1998 SLP .SAV 13P 31-Oct-1998 DUMP .SAV 10P 31-Oct-1998 SIPP .SAV 21P 31-Oct-1998 BUP .SAV 68P 31-Oct-1998 PAT .SAV 11P 31-Oct-1998 HELP .SAV 161P 31-Oct-1998 SYSMAC.SML 92P 31-Oct-1998 SYSLIB.OBJ 84P 31-Oct-1998 FORMAT.SAV 28P 31-Oct-1998 SETUP .SAV 43P 31-Oct-1998 VTCOM .SAV 24P 31-Oct-1998 DATIME.SAV 4P 31-Oct-1998 DATIME.MAC 23P 31-Oct-1998 DATIME.COM 3P 31-Oct-1998 LET .SAV 6P 31-Oct-1998 SPLIT .SAV 3P 31-Oct-1998 UCL .SAV 16P 31-Oct-1998 VBGEXE.SAV 18P 31-Oct-1998 TERMID.SAV 4P 31-Oct-1998 TRANSF.SAV 16P 31-Oct-1998 TRANSF.TSK 76P 31-Oct-1998 TRANSF.EXE 45P 31-Oct-1998 ODT .OBJ 8P 31-Oct-1998 VDT .OBJ 8P 31-Oct-1998 MDUP .SAV 22P 31-Oct-1998 MBOOT .BOT 1P 31-Oct-1998 MBOT16.BOT 1P 31-Oct-1998 MSBOOT.BOT 4P 31-Oct-1998 MDUP .AI 72P 31-Oct-1998 MDUP .MM 72P 31-Oct-1998 MDUP .MS 72P 31-Oct-1998 MDUP .MT 72P 31-Oct-1998 MDUP .MU 72P 31-Oct-1998 VERIFY.COM 2P 31-Oct-1998 IVP .COM 16P 31-Oct-1998 IVP .MAC 33P 31-Oct-1998 MTB .COM 16P 31-Oct-1998 MSB .COM 16P 31-Oct-1998 MUB .COM 16P 31-Oct-1998 SB .MAC 1P 31-Oct-1998 FB .MAC 1P 31-Oct-1998 XM .MAC 1P 31-Oct-1998 XB .MAC 1P 31-Oct-1998 ZM .MAC 1P 31-Oct-1998 ZB .MAC 1P 31-Oct-1998 SYSTEM.MLB 148P 31-Oct-1998 EDTL .MLB 11P 31-Oct-1998 SYSGEN.COM 286P 31-Oct-1998 CONFIG.COM 29P 31-Oct-1998 CONFIG.SAV 10P 31-Oct-1998 V5USER.TXT 2P 31-Oct-1998 V5NOTE.TXT 36P 31-Oct-1998 CUSTOM.TXT 14P 31-Oct-1998 MSCPCK.SAV 4P 31-Oct-1998 DBGSYM.SAV 10P 31-Oct-1998 INDEX .SAV 11P 31-Oct-1998 INDEXX.SAV 14P 31-Oct-1998 INDEXA.IMG 164P 31-Oct-1998 INDEXB.IMG 165P 31-Oct-1998 INDEX .IDX 7P 31-Oct-1998 TECO .SAV 50P 31-Oct-1998 SGN02 .CND 5P 02-Oct-2020 SGN02 .ANS 9P 02-Oct-2020 SGN02 .BLD 3P 02-Oct-2020 SGN02 .MON 10P 02-Oct-2020 SGN02 .DEV 6P 02-Oct-2020 SGN02 .TBL 5P 02-Oct-2020 RT11SB.MAP 34P 02-Oct-2020 RT11FB.MAP 35P 02-Oct-2020 RT11XM.MAP 38P 02-Oct-2020 RT11XB.MAP 36P 02-Oct-2020 RT11ZM.MAP 38P 02-Oct-2020 RT11ZB.MAP 36P 02-Oct-2020 STRTSB.COM 1P 31-Oct-1998 STRTFB.COM 5P 31-Oct-1998 STRTXM.COM 8P 31-Oct-1998 STRTXB.COM 5P 31-Oct-1998 STRTZM.COM 8P 31-Oct-1998 STRTZB.COM 5P 31-Oct-1998 HELAY .SYS 1 13-Jun-1988 EM .SYS 4 04-Mar-2012 TSYB10.COM 1 16-Oct-2020 TSYNL .COM 1 16-Oct-2020 141 Files, 4116 Blocks 37376 Free blocks .DAT 10-MAR-2021 .TIM 14:00 .@TSYNL .TIME 14:00:10 .COPY/DEVICE/NOQUERY SY: NL: .TIME 14:01:38 .
- - - Добавлено - - -
Ну, на этом интерес к RQDX3 исчерпан
Последний раз редактировалось Hunta; 12.03.2021 в 09:45.
Поскольку тут ко мне поступили... некие предложения... Уточняю - интерес исчерпан не значит, что она мне больше не нужна. Мысли на её счёт у меня есть, так что пока она останется у меня.
По ряду причин прогнал копирование CF-ки (точнее 65534 блоков) в NL:
KDJ11-B показала 537 кб/с
KDF-11B показала 207 кб/с
KDJ11-B у меня разогнанная при паспортном кварце на 18 МГц на плате стоит кварц на 24, то есть вместо 4.5 лимонов регистр-регистр – шарашит 6
Поскольку периодически мне хочется странного и поскольку для втыкания странного периодически оказывается, что корзинка не та...
После некоторых размышлений и покупок родилось НЕЧТО
Нечто слегка недоделанной (с одной из сторон) доделаю - перефотографирую
xolod(20.03.2021)
Эту тему просматривают: 1 (пользователей: 0 , гостей: 1)
Ваши права
Ответить с цитированием
