Расширяю функционал :)
.RUN CFUTIL GETINFO 100:1:161140 TO TT:
Getting info...
General configuration : 102212
Removable device : X
Non-removable device :
Default number of cylinders : 31045
Default number of heads : 16
Default number of sectors per track : 63
Number of sectors per card : 31293360
Serial number : AAZ080619085119
Number of ECC bytes passed on Read/Write Long Commands : 4
Firmware revision : HDX16.01
Model number : SDCFHS-016G
Maximum number of sectors on Read/Write Multiple : 100001
Capabilities : 7400
Standby Timer supported :
IORDY supported : X
IORDY may be disabled : X
LBA supported : X
DMA supported : X
PIO data transfer cycle timing mode : 2
Translation Parameters Valid : 7
Curr num of cyls, heads, sectors and capacity valid : X
Adv PIO modes, MW DMA and Min PIO xfrr cycle valid : X
Ultra DMA Modes valid : X
Current numbers of cylinders : 31045
Current numbers of heads : 16
Current sectors per track : 63
Current capacity in sectors (LBA) : 31293360
Multiple sector setting : 0
Multiple sector setting valid : X
Total number of sectors addressable in LBA Mode : 31293360
Multiword DMA transfer : 7
Multiword DMA mode 0 supported : X
Multiword DMA mode 1 supported : X
Multiword DMA mode 2 supported : X
Multiword DMA mode 0 selected :
Multiword DMA mode 1 selected :
Multiword DMA mode 2 selected :
Advanced PIO modes supported : 3
PIO mode 3 supported : X
PIO mode 4 supported : X
PIO mode 3 selected :
PIO mode 4 selected :
Minimum Multiword DMA transfer cycle time per word, ns : 170
Recommended Multiword DMA transfer cycle time, ns : 170
Minimum PIO transfer cycle time without flow control, ns : 170
Minimum PIO transfer cycle time with IORDY flow control, ns: 170
Features/command sets supported :
SMART feature set is supported : X
Security Mode feature set is supported :
Removable Media feature set is supported :
Power Management feature set is supported : X
Packet Command feature set is supported :
Write cache is supported : X
Look-ahead is supported :
Release interrupt is supported :
Service interrupt is supported :
Device Reset command is supported :
Host Protected Area feature set is supported :
Write Buffer command is supported : X
Read Buffer command is supported : X
NOP command is supported : X
Download Microcode command is supported :
Read/Write DMA Queued commands is supported :
CFA feature set command is supported : X
Advanced Power Management feature set is supported : X
Removable Media Status feature set is supported :
Features/command sets enabled :
SMART feature set has been enabled :
Security Mode feature set has been enabled :
Removable Media feature set has been enabled :
Power Management feature set has been enabled :
Packet Command feature set has been enabled :
Write cache has been enabled :
Look-ahead has been enabled :
Release interrupt has been enabled :
Service interrupt has been enabled :
Device Reset command has been enabled :
Host Protected Area feature set has been enabled :
Write Buffer command has been enabled :
Read Buffer command has been enabled :
NOP command has been enabled :
Download Microcode command has been enabled :
Read/Write DMA Queued commands has been enabled :
CFA feature set command has been enabled :
Advanced Power Management feature set has been enabled :
Removable Media Status feature set has been enabled :
Ultra DMA Mode Supported and Selected : 377
Time required for Security erase unit completion : 0
Time required for Enhanced security erase unit completion : 0
Current Advanced power management value : 0
Security status : 0
Vendor unique bytes :
Power requirement description : 100764
Reserved for assignment by the CFA : 0
Key management schemes supported : 0
CF Advanced True IDE Timing Mode Capability and Setting : 222
CF Advanced PC Card I/O and Memory Timing Mode Capability : 0
.
- - - Добавлено - - -
Как выглядит описание, по которому идёт расшифровка
CF$DSC 0, 2, D$W, , <General configuration>
CF$DSC 0, 2, D$BIT, 7. , <Removable device>
CF$DSC 0, 2, D$BIT, 6. , <Non-removable device>
CF$DSC 1, 2, D$W10, , <Default number of cylinders>
; CF$DSC 2, 2, D$W, , <Reserved>
CF$DSC 3, 2, D$W10, , <Default number of heads>
; CF$DSC 4, 2, D$W, , <Obsolete>
; CF$DSC 5, 2, D$W, , <Obsolete>
CF$DSC 6, 2, D$W10, , <Default number of sectors per track>
CF$DSC 7, 4, D$DE10, , <Number of sectors per card>
; CF$DSC 9, 2, D$W, , <Obsolete>
CF$DSC 10, 20, D$STR, , <Serial number>
; CF$DSC 20, 2, D$W, , <Obsolete>
; CF$DSC 21, 2, D$W, , <Obsolete>
CF$DSC 22, 2, D$W, , <Number of ECC bytes passed on Read/Write Long Commands>
CF$DSC 23, 8, D$STR, , <Firmware revision>
CF$DSC 27, 40, D$STR, , <Model number>
CF$DSC 47, 2, D$W, , <Maximum number of sectors on Read/Write Multiple>
; CF$DSC 48, 2, D$W, , <Reserved>
CF$DSC 49, 2, D$W, , <Capabilities>
CF$DSC 49, 2, D$BIT, 13. , <Standby Timer supported>
CF$DSC 49, 2, D$BIT, 11. , <IORDY supported>
CF$DSC 49, 2, D$BIT, 10. , <IORDY may be disabled>
CF$DSC 49, 2, D$BIT, 9. , <LBA supported>
CF$DSC 49, 2, D$BIT, 8. , <DMA supported>
; CF$DSC 50, 2, D$W, , <Reserved>
CF$DSC 51, 2, D$HB, , <PIO data transfer cycle timing mode>
; CF$DSC 52, 2, D$W, , <Obsolete>
CF$DSC 53, 2, D$W, , <Translation Parameters Valid>
CF$DSC 53, 2, D$BIT, 0. , <Curr num of cyls, heads, sectors and capacity valid>
CF$DSC 53, 2, D$BIT, 1. , <Adv PIO modes, MW DMA and Min PIO xfrr cycle valid>
CF$DSC 53, 2, D$BIT, 2. , <Ultra DMA Modes valid>
CF$DSC 54, 2, D$W10, , <Current numbers of cylinders>
CF$DSC 55, 2, D$W10, , <Current numbers of heads>
CF$DSC 56, 2, D$W10, , <Current sectors per track>
CF$DSC 57, 4, D$DW10, , <Current capacity in sectors (LBA)>
CF$DSC 59, 2, D$LB, , <Multiple sector setting>
CF$DSC 59, 2, D$BIT, 8. , <Multiple sector setting valid>
CF$DSC 60, 4, D$DW10, , <Total number of sectors addressable in LBA Mode>
; CF$DSC 62, 2, D$W, , <Reserved>
CF$DSC 63, 2, D$W, , <Multiword DMA transfer>
CF$DSC 63, 2, D$BIT, 0. , <Multiword DMA mode 0 supported>
CF$DSC 63, 2, D$BIT, 1. , <Multiword DMA mode 1 supported>
CF$DSC 63, 2, D$BIT, 2. , <Multiword DMA mode 2 supported>
CF$DSC 63, 2, D$BIT, 8. , <Multiword DMA mode 0 selected>
CF$DSC 63, 2, D$BIT, 9. , <Multiword DMA mode 1 selected>
CF$DSC 63, 2, D$BIT, 10. , <Multiword DMA mode 2 selected>
CF$DSC 64, 2, D$W, , <Advanced PIO modes supported>
CF$DSC 64, 2, D$BIT, 0. , <PIO mode 3 supported>
CF$DSC 64, 2, D$BIT, 1. , <PIO mode 4 supported>
CF$DSC 64, 2, D$BIT, 8. , <PIO mode 3 selected>
CF$DSC 64, 2, D$BIT, 9. , <PIO mode 4 selected>
CF$DSC 65, 2, D$W, , <Minimum Multiword DMA transfer cycle time per word, ns>
CF$DSC 66, 2, D$W, , <Recommended Multiword DMA transfer cycle time, ns>
CF$DSC 67, 2, D$W, , <Minimum PIO transfer cycle time without flow control, ns>
CF$DSC 68, 2, D$W, , <Minimum PIO transfer cycle time with IORDY flow control, ns>
; CF$DSC 69, 20, D$NOSHOW, , <Reserved>
; CF$DSC 80, 4, D$DW, , <Reserved>
CF$DSC 82, 6, D$PROC, DPROC1, <Features/command sets supported>
CF$DSC 82, 2, D$BIT, 0. , <SMART feature set is supported>
CF$DSC 82, 2, D$BIT, 1. , <Security Mode feature set is supported>
CF$DSC 82, 2, D$BIT, 2. , <Removable Media feature set is supported>
CF$DSC 82, 2, D$BIT, 3. , <Power Management feature set is supported>
CF$DSC 82, 2, D$BIT, 4. , <Packet Command feature set is supported>
CF$DSC 82, 2, D$BIT, 5. , <Write cache is supported>
CF$DSC 82, 2, D$BIT, 6. , <Look-ahead is supported>
CF$DSC 82, 2, D$BIT, 7. , <Release interrupt is supported>
CF$DSC 82, 2, D$BIT, 8. , <Service interrupt is supported>
CF$DSC 82, 2, D$BIT, 9. , <Device Reset command is supported>
CF$DSC 82, 2, D$BIT, 10. , <Host Protected Area feature set is supported>
; CF$DSC 82, 2, D$BIT, 11. , <Obsolete>
CF$DSC 82, 2, D$BIT, 12. , <Write Buffer command is supported>
CF$DSC 82, 2, D$BIT, 13. , <Read Buffer command is supported>
CF$DSC 82, 2, D$BIT, 14. , <NOP command is supported>
; CF$DSC 82, 2, D$BIT, 15. , <Obsolete>
CF$DSC 82, 2, D$BIT, 16. , <Download Microcode command is supported>
CF$DSC 82, 2, D$BIT, 17. , <Read/Write DMA Queued commands is supported>
CF$DSC 82, 2, D$BIT, 18. , <CFA feature set command is supported>
CF$DSC 82, 2, D$BIT, 19. , <Advanced Power Management feature set is supported>
CF$DSC 82, 2, D$BIT, 20. , <Removable Media Status feature set is supported>
CF$DSC 85, 6, D$PROC, DPROC2, <Features/command sets enabled>
CF$DSC 85, 2, D$BIT, 0. , <SMART feature set has been enabled>
CF$DSC 85, 2, D$BIT, 1. , <Security Mode feature set has been enabled>
CF$DSC 85, 2, D$BIT, 2. , <Removable Media feature set has been enabled>
CF$DSC 85, 2, D$BIT, 3. , <Power Management feature set has been enabled>
CF$DSC 85, 2, D$BIT, 4. , <Packet Command feature set has been enabled>
CF$DSC 85, 2, D$BIT, 5. , <Write cache has been enabled>
CF$DSC 85, 2, D$BIT, 6. , <Look-ahead has been enabled>
CF$DSC 85, 2, D$BIT, 7. , <Release interrupt has been enabled>
CF$DSC 85, 2, D$BIT, 8. , <Service interrupt has been enabled>
CF$DSC 85, 2, D$BIT, 9. , <Device Reset command has been enabled>
CF$DSC 85, 2, D$BIT, 10. , <Host Protected Area feature set has been enabled>
; CF$DSC 85, 2, D$BIT, 11. , <Obsolete>
CF$DSC 85, 2, D$BIT, 12. , <Write Buffer command has been enabled>
CF$DSC 85, 2, D$BIT, 13. , <Read Buffer command has been enabled>
CF$DSC 85, 2, D$BIT, 14. , <NOP command has been enabled>
; CF$DSC 85, 2, D$BIT, 15. , <Obsolete>
CF$DSC 85, 2, D$BIT, 16. , <Download Microcode command has been enabled>
CF$DSC 85, 2, D$BIT, 17. , <Read/Write DMA Queued commands has been enabled>
CF$DSC 85, 2, D$BIT, 18. , <CFA feature set command has been enabled>
CF$DSC 85, 2, D$BIT, 19. , <Advanced Power Management feature set has been enabled>
CF$DSC 85, 2, D$BIT, 20. , <Removable Media Status feature set has been enabled>
CF$DSC 88, 2, D$W, , <Ultra DMA Mode Supported and Selected>
CF$DSC 89, 2, D$W, , <Time required for Security erase unit completion>
CF$DSC 90, 2, D$W, , <Time required for Enhanced security erase unit completion>
CF$DSC 91, 2, D$W, , <Current Advanced power management value>
; CF$DSC 92, 72, D$NOSHOW, , <Reserved>
CF$DSC 128, 2, D$W, , <Security status>
CF$DSC 129, 64, D$BS, , <Vendor unique bytes>
CF$DSC 160, 2, D$W, , <Power requirement description>
CF$DSC 161, 2, D$W, , <Reserved for assignment by the CFA>
CF$DSC 162, 2, D$W, , <Key management schemes supported>
CF$DSC 163, 2, D$W, , <CF Advanced True IDE Timing Mode Capability and Setting>
CF$DSC 164, 2, D$W, , <CF Advanced PC Card I/O and Memory Timing Mode Capability>
; CF$DSC 165, 6, D$BS, , <Reserved for assignment by the CFA>
; CF$DSC 168, 158, D$NOSHOW, , <Reserved>
CF$DSC , , D$END