А где эта "помойка" ?
А почему бы не составить и поддерживать (и Вам и всем заинтересованным форумцам) ? Разве не полезно было бы ?Цитата:
Сообщение от Hunta
Эта - известна, а еще ?Цитата:
Сообщение от Hunta
Вид для печати
А где эта "помойка" ?
А почему бы не составить и поддерживать (и Вам и всем заинтересованным форумцам) ? Разве не полезно было бы ?Цитата:
Сообщение от Hunta
Эта - известна, а еще ?Цитата:
Сообщение от Hunta
Потому что свободного времени мало и занято оно другим, как правилоЦитата:
Сообщение от ra3qdp
Судя по количество запросов с просьбой выложить (конкретику) - нетЦитата:
Сообщение от ra3qdp
Ищущий да обращетЦитата:
Сообщение от ra3qdp
почему так ? Что Вы думаете ?Цитата:
Сообщение от Hunta
Меня это не волнуетЦитата:
Сообщение от ra3qdp
Даже не знаю, в какую тему засунуть :) Поэтому сюда :)
Код:.RUN CFUTIL GETINFO 100:1:161000 TO TT:
Getting info...
General configuration : 2112
Default number of cylinders : 487
Reserved : 0
Default number of heads : 16
Obsolete : 0
Obsolete : 1100
Default number of sectors per track : 63
Number of sectors per card : 490896
Obsolete : 0
Serial number : STP21240N33
Obsolete : 2
Obsolete : 2
Number of ECC bytes passed on Read/Write Long Commands : 4
Firmware revision : 20130902
Model number : SMART CF
Maximum number of sectors on Read/Write Multiple : 100001
Reserved : 0
Capabilities : 7400
Reserved : 0
PIO data transfer cycle timing mode : 1000
Obsolete : 0
Field Validity : 7
Current numbers of cylinders : 487
Current numbers of heads : 16
Current sectors per track : 63
Current capacity in sectors (LBA) : 490896
Multiple sector setting : 400
Total number of sectors addressable in LBA Mode : 490896
Reserved : 0
Multiword DMA transfer : 7
Advanced PIO modes supported : 3
Minimum Multiword DMA transfer cycle time per word : 170
Recommended Multiword DMA transfer cycle time : 170
Minimum PIO transfer cycle time without flow control : 170
Minimum PIO transfer cycle time with IORDY flow control : 170
Reserved :
Reserved :
Features/command sets supported :
Features/command sets enabled :
Ultra DMA Mode Supported and Selected : 77
Time required for Security erase unit completion : 0
Time required for Enhanced security erase unit completion: 0
Current Advanced power management value : 0
Reserved :
Security status : 0
Vendor unique bytes :
Power requirement description : 140040
Reserved for assignment by the CFA : 0
Key management schemes supported : 0
CF Advanced True IDE Timing Mode Capability and Setting : 222
CF Advanced PC Card I/O and Memory Timing Mode Capability: 0
Reserved for assignment by the CFA :
Reserved :
Табличный парсер, ещё не всё дописано, поэтому не всё и что то не совсем так показывается. Но что то можно использовать :) CF - CISCO на 256 Мб и (ЕМНИП) SanDisk на 16 ГбКод:.RUN CFUTIL GETINFO 100:1:161140 TO TT:
Getting info...
General configuration : 102212
Default number of cylinders : 31045
Reserved : 0
Default number of heads : 16
Obsolete : 0
Obsolete : 0
Default number of sectors per track : 63
Number of sectors per card : 31293360
Obsolete : 0
Serial number : AAZ080619085119
Obsolete : 2
Obsolete : 2
Number of ECC bytes passed on Read/Write Long Commands : 4
Firmware revision : HDX16.01
Model number : SDCFHS-016G
Maximum number of sectors on Read/Write Multiple : 100001
Reserved : 0
Capabilities : 7400
Reserved : 0
PIO data transfer cycle timing mode : 1000
Obsolete : 0
Field Validity : 7
Current numbers of cylinders : 31045
Current numbers of heads : 16
Current sectors per track : 63
Current capacity in sectors (LBA) : 31293360
Multiple sector setting : 110400
Total number of sectors addressable in LBA Mode : 31293360
Reserved : 0
Multiword DMA transfer : 7
Advanced PIO modes supported : 3
Minimum Multiword DMA transfer cycle time per word : 170
Recommended Multiword DMA transfer cycle time : 170
Minimum PIO transfer cycle time without flow control : 170
Minimum PIO transfer cycle time with IORDY flow control : 170
Reserved :
Reserved :
Features/command sets supported :
Features/command sets enabled :
Ultra DMA Mode Supported and Selected : 377
Time required for Security erase unit completion : 0
Time required for Enhanced security erase unit completion: 0
Current Advanced power management value : 0
Reserved :
Security status : 0
Vendor unique bytes :
Power requirement description : 100764
Reserved for assignment by the CFA : 0
Key management schemes supported : 0
CF Advanced True IDE Timing Mode Capability and Setting : 222
CF Advanced PC Card I/O and Memory Timing Mode Capability: 0
Reserved for assignment by the CFA :
Reserved :
.
Расширяю функционал :)
- - - Добавлено - - -Код:.RUN CFUTIL GETINFO 100:1:161140 TO TT:
Getting info...
General configuration : 102212
Removable device : X
Non-removable device :
Default number of cylinders : 31045
Default number of heads : 16
Default number of sectors per track : 63
Number of sectors per card : 31293360
Serial number : AAZ080619085119
Number of ECC bytes passed on Read/Write Long Commands : 4
Firmware revision : HDX16.01
Model number : SDCFHS-016G
Maximum number of sectors on Read/Write Multiple : 100001
Capabilities : 7400
Standby Timer supported :
IORDY supported : X
IORDY may be disabled : X
LBA supported : X
DMA supported : X
PIO data transfer cycle timing mode : 2
Translation Parameters Valid : 7
Curr num of cyls, heads, sectors and capacity valid : X
Adv PIO modes, MW DMA and Min PIO xfrr cycle valid : X
Ultra DMA Modes valid : X
Current numbers of cylinders : 31045
Current numbers of heads : 16
Current sectors per track : 63
Current capacity in sectors (LBA) : 31293360
Multiple sector setting : 0
Multiple sector setting valid : X
Total number of sectors addressable in LBA Mode : 31293360
Multiword DMA transfer : 7
Multiword DMA mode 0 supported : X
Multiword DMA mode 1 supported : X
Multiword DMA mode 2 supported : X
Multiword DMA mode 0 selected :
Multiword DMA mode 1 selected :
Multiword DMA mode 2 selected :
Advanced PIO modes supported : 3
PIO mode 3 supported : X
PIO mode 4 supported : X
PIO mode 3 selected :
PIO mode 4 selected :
Minimum Multiword DMA transfer cycle time per word, ns : 170
Recommended Multiword DMA transfer cycle time, ns : 170
Minimum PIO transfer cycle time without flow control, ns : 170
Minimum PIO transfer cycle time with IORDY flow control, ns: 170
Features/command sets supported :
SMART feature set is supported : X
Security Mode feature set is supported :
Removable Media feature set is supported :
Power Management feature set is supported : X
Packet Command feature set is supported :
Write cache is supported : X
Look-ahead is supported :
Release interrupt is supported :
Service interrupt is supported :
Device Reset command is supported :
Host Protected Area feature set is supported :
Write Buffer command is supported : X
Read Buffer command is supported : X
NOP command is supported : X
Download Microcode command is supported :
Read/Write DMA Queued commands is supported :
CFA feature set command is supported : X
Advanced Power Management feature set is supported : X
Removable Media Status feature set is supported :
Features/command sets enabled :
SMART feature set has been enabled :
Security Mode feature set has been enabled :
Removable Media feature set has been enabled :
Power Management feature set has been enabled :
Packet Command feature set has been enabled :
Write cache has been enabled :
Look-ahead has been enabled :
Release interrupt has been enabled :
Service interrupt has been enabled :
Device Reset command has been enabled :
Host Protected Area feature set has been enabled :
Write Buffer command has been enabled :
Read Buffer command has been enabled :
NOP command has been enabled :
Download Microcode command has been enabled :
Read/Write DMA Queued commands has been enabled :
CFA feature set command has been enabled :
Advanced Power Management feature set has been enabled :
Removable Media Status feature set has been enabled :
Ultra DMA Mode Supported and Selected : 377
Time required for Security erase unit completion : 0
Time required for Enhanced security erase unit completion : 0
Current Advanced power management value : 0
Security status : 0
Vendor unique bytes :
Power requirement description : 100764
Reserved for assignment by the CFA : 0
Key management schemes supported : 0
CF Advanced True IDE Timing Mode Capability and Setting : 222
CF Advanced PC Card I/O and Memory Timing Mode Capability : 0
.
Как выглядит описание, по которому идёт расшифровка
Код:CF$DSC 0, 2, D$W, , <General configuration>
CF$DSC 0, 2, D$BIT, 7. , <Removable device>
CF$DSC 0, 2, D$BIT, 6. , <Non-removable device>
CF$DSC 1, 2, D$W10, , <Default number of cylinders>
; CF$DSC 2, 2, D$W, , <Reserved>
CF$DSC 3, 2, D$W10, , <Default number of heads>
; CF$DSC 4, 2, D$W, , <Obsolete>
; CF$DSC 5, 2, D$W, , <Obsolete>
CF$DSC 6, 2, D$W10, , <Default number of sectors per track>
CF$DSC 7, 4, D$DE10, , <Number of sectors per card>
; CF$DSC 9, 2, D$W, , <Obsolete>
CF$DSC 10, 20, D$STR, , <Serial number>
; CF$DSC 20, 2, D$W, , <Obsolete>
; CF$DSC 21, 2, D$W, , <Obsolete>
CF$DSC 22, 2, D$W, , <Number of ECC bytes passed on Read/Write Long Commands>
CF$DSC 23, 8, D$STR, , <Firmware revision>
CF$DSC 27, 40, D$STR, , <Model number>
CF$DSC 47, 2, D$W, , <Maximum number of sectors on Read/Write Multiple>
; CF$DSC 48, 2, D$W, , <Reserved>
CF$DSC 49, 2, D$W, , <Capabilities>
CF$DSC 49, 2, D$BIT, 13. , <Standby Timer supported>
CF$DSC 49, 2, D$BIT, 11. , <IORDY supported>
CF$DSC 49, 2, D$BIT, 10. , <IORDY may be disabled>
CF$DSC 49, 2, D$BIT, 9. , <LBA supported>
CF$DSC 49, 2, D$BIT, 8. , <DMA supported>
; CF$DSC 50, 2, D$W, , <Reserved>
CF$DSC 51, 2, D$HB, , <PIO data transfer cycle timing mode>
; CF$DSC 52, 2, D$W, , <Obsolete>
CF$DSC 53, 2, D$W, , <Translation Parameters Valid>
CF$DSC 53, 2, D$BIT, 0. , <Curr num of cyls, heads, sectors and capacity valid>
CF$DSC 53, 2, D$BIT, 1. , <Adv PIO modes, MW DMA and Min PIO xfrr cycle valid>
CF$DSC 53, 2, D$BIT, 2. , <Ultra DMA Modes valid>
CF$DSC 54, 2, D$W10, , <Current numbers of cylinders>
CF$DSC 55, 2, D$W10, , <Current numbers of heads>
CF$DSC 56, 2, D$W10, , <Current sectors per track>
CF$DSC 57, 4, D$DW10, , <Current capacity in sectors (LBA)>
CF$DSC 59, 2, D$LB, , <Multiple sector setting>
CF$DSC 59, 2, D$BIT, 8. , <Multiple sector setting valid>
CF$DSC 60, 4, D$DW10, , <Total number of sectors addressable in LBA Mode>
; CF$DSC 62, 2, D$W, , <Reserved>
CF$DSC 63, 2, D$W, , <Multiword DMA transfer>
CF$DSC 63, 2, D$BIT, 0. , <Multiword DMA mode 0 supported>
CF$DSC 63, 2, D$BIT, 1. , <Multiword DMA mode 1 supported>
CF$DSC 63, 2, D$BIT, 2. , <Multiword DMA mode 2 supported>
CF$DSC 63, 2, D$BIT, 8. , <Multiword DMA mode 0 selected>
CF$DSC 63, 2, D$BIT, 9. , <Multiword DMA mode 1 selected>
CF$DSC 63, 2, D$BIT, 10. , <Multiword DMA mode 2 selected>
CF$DSC 64, 2, D$W, , <Advanced PIO modes supported>
CF$DSC 64, 2, D$BIT, 0. , <PIO mode 3 supported>
CF$DSC 64, 2, D$BIT, 1. , <PIO mode 4 supported>
CF$DSC 64, 2, D$BIT, 8. , <PIO mode 3 selected>
CF$DSC 64, 2, D$BIT, 9. , <PIO mode 4 selected>
CF$DSC 65, 2, D$W, , <Minimum Multiword DMA transfer cycle time per word, ns>
CF$DSC 66, 2, D$W, , <Recommended Multiword DMA transfer cycle time, ns>
CF$DSC 67, 2, D$W, , <Minimum PIO transfer cycle time without flow control, ns>
CF$DSC 68, 2, D$W, , <Minimum PIO transfer cycle time with IORDY flow control, ns>
; CF$DSC 69, 20, D$NOSHOW, , <Reserved>
; CF$DSC 80, 4, D$DW, , <Reserved>
CF$DSC 82, 6, D$PROC, DPROC1, <Features/command sets supported>
CF$DSC 82, 2, D$BIT, 0. , <SMART feature set is supported>
CF$DSC 82, 2, D$BIT, 1. , <Security Mode feature set is supported>
CF$DSC 82, 2, D$BIT, 2. , <Removable Media feature set is supported>
CF$DSC 82, 2, D$BIT, 3. , <Power Management feature set is supported>
CF$DSC 82, 2, D$BIT, 4. , <Packet Command feature set is supported>
CF$DSC 82, 2, D$BIT, 5. , <Write cache is supported>
CF$DSC 82, 2, D$BIT, 6. , <Look-ahead is supported>
CF$DSC 82, 2, D$BIT, 7. , <Release interrupt is supported>
CF$DSC 82, 2, D$BIT, 8. , <Service interrupt is supported>
CF$DSC 82, 2, D$BIT, 9. , <Device Reset command is supported>
CF$DSC 82, 2, D$BIT, 10. , <Host Protected Area feature set is supported>
; CF$DSC 82, 2, D$BIT, 11. , <Obsolete>
CF$DSC 82, 2, D$BIT, 12. , <Write Buffer command is supported>
CF$DSC 82, 2, D$BIT, 13. , <Read Buffer command is supported>
CF$DSC 82, 2, D$BIT, 14. , <NOP command is supported>
; CF$DSC 82, 2, D$BIT, 15. , <Obsolete>
CF$DSC 82, 2, D$BIT, 16. , <Download Microcode command is supported>
CF$DSC 82, 2, D$BIT, 17. , <Read/Write DMA Queued commands is supported>
CF$DSC 82, 2, D$BIT, 18. , <CFA feature set command is supported>
CF$DSC 82, 2, D$BIT, 19. , <Advanced Power Management feature set is supported>
CF$DSC 82, 2, D$BIT, 20. , <Removable Media Status feature set is supported>
CF$DSC 85, 6, D$PROC, DPROC2, <Features/command sets enabled>
CF$DSC 85, 2, D$BIT, 0. , <SMART feature set has been enabled>
CF$DSC 85, 2, D$BIT, 1. , <Security Mode feature set has been enabled>
CF$DSC 85, 2, D$BIT, 2. , <Removable Media feature set has been enabled>
CF$DSC 85, 2, D$BIT, 3. , <Power Management feature set has been enabled>
CF$DSC 85, 2, D$BIT, 4. , <Packet Command feature set has been enabled>
CF$DSC 85, 2, D$BIT, 5. , <Write cache has been enabled>
CF$DSC 85, 2, D$BIT, 6. , <Look-ahead has been enabled>
CF$DSC 85, 2, D$BIT, 7. , <Release interrupt has been enabled>
CF$DSC 85, 2, D$BIT, 8. , <Service interrupt has been enabled>
CF$DSC 85, 2, D$BIT, 9. , <Device Reset command has been enabled>
CF$DSC 85, 2, D$BIT, 10. , <Host Protected Area feature set has been enabled>
; CF$DSC 85, 2, D$BIT, 11. , <Obsolete>
CF$DSC 85, 2, D$BIT, 12. , <Write Buffer command has been enabled>
CF$DSC 85, 2, D$BIT, 13. , <Read Buffer command has been enabled>
CF$DSC 85, 2, D$BIT, 14. , <NOP command has been enabled>
; CF$DSC 85, 2, D$BIT, 15. , <Obsolete>
CF$DSC 85, 2, D$BIT, 16. , <Download Microcode command has been enabled>
CF$DSC 85, 2, D$BIT, 17. , <Read/Write DMA Queued commands has been enabled>
CF$DSC 85, 2, D$BIT, 18. , <CFA feature set command has been enabled>
CF$DSC 85, 2, D$BIT, 19. , <Advanced Power Management feature set has been enabled>
CF$DSC 85, 2, D$BIT, 20. , <Removable Media Status feature set has been enabled>
CF$DSC 88, 2, D$W, , <Ultra DMA Mode Supported and Selected>
CF$DSC 89, 2, D$W, , <Time required for Security erase unit completion>
CF$DSC 90, 2, D$W, , <Time required for Enhanced security erase unit completion>
CF$DSC 91, 2, D$W, , <Current Advanced power management value>
; CF$DSC 92, 72, D$NOSHOW, , <Reserved>
CF$DSC 128, 2, D$W, , <Security status>
CF$DSC 129, 64, D$BS, , <Vendor unique bytes>
CF$DSC 160, 2, D$W, , <Power requirement description>
CF$DSC 161, 2, D$W, , <Reserved for assignment by the CFA>
CF$DSC 162, 2, D$W, , <Key management schemes supported>
CF$DSC 163, 2, D$W, , <CF Advanced True IDE Timing Mode Capability and Setting>
CF$DSC 164, 2, D$W, , <CF Advanced PC Card I/O and Memory Timing Mode Capability>
; CF$DSC 165, 6, D$BS, , <Reserved for assignment by the CFA>
; CF$DSC 168, 158, D$NOSHOW, , <Reserved>
CF$DSC , , D$END
Руки добрались до RQDX3. Для соединения с платой расширения использовал кабель, который на microvax-ах используется для соединение платы процессора и плат памяти - IDE50, прямое соединение контактов между разъёмами - что ещё нужно для соединения плат :)
Под раздачу попал Seagate ST-124 - 615x4x17 - примерно 20 мб. Форматирование и тестирования программой ZRQC прошло успешно. Сейчас идёт копирование системы.
В системе уже стоит плата CMD-420 как основной контроллер DU, так что для этой переставил CSR на альтернативный адрес.
- - - Добавлено - - -
К сожалению, загрузка не идёт ни в каком виде. Попробую поставить CSR на стандартный и загрузитьсяКод:Commands are Help, Boot, List, Setup, Map and Test.
Type a command then press the RETURN key: BOO DU0
Trying DU0
Starting system from DU0
BOOTING UP XXDP-XM EXTENDED MONITOR
XXDP-XM EXTENDED MONITOR - XXDP V2.5
REVISION: F0
BOOTED FROM DU0
124KW OF MEMORY
NON-UNIBUS SYSTEM
RESTART ADDRESS: 152000
TYPE "H" FOR HELP !
.R ZRQC??
ZRQCF0.BIN
DRSSM-G2
ZRQC-F-0
RQDX3 Disk Formatter Utility
UNIT IS Formattable Winchester (RDnn) or Floppy (RX33) Drives
RSTRT ADR 145702
DR>START
CHANGE HW (L) ? Y
# UNITS (D) ? 1
UNIT 0
Enter controller IP Address (O) 172150 ? 172160
Do you want to use the "AUTOFORMAT" Mode [Y/N] (L) Y ? N
**** WARNING ****
ALL DATA ON SELECTED DRIVE WILL BE DESTROYED
Write protect all drives not being formatted.
Please verify that the selected drive is ON LINE
and NOT write protected.
If formatting RX33 media, insert media to be
formatted in the selected drive.
Do you wish to continue [Y/N] (L) N ? Y
MSCP Controller Model: 19
Microcode Version: 4
What unit do you want to format [0-255] (A) ? 0
Do you want to use manufacturing bad block information [Y/N] (A) N ?
Downline load UIT [Y/N] (A) Y ?
UIT Drive Name
_______________________________________________________
0 RD51
1 RD52 part # 30-21721-02 (1 light on front panel)
2 RD52 part # 30-23227-02 (2 lights on front panel)
3 RD53
4 RD31
5 RD54
6 RD32
Enter Unit Identifier Table (UIT) [0-6] (D) ? 4
Continue if bad block information is inaccessible [Y/N] (A) N ? Y
Please type in the serial number [8-10 digits] (A) ? 1234567890
Formatting of Drive 0 Begun -- Total number of LBN's to format is 41584.
------------ FORMAT PROGRESS REPORT -------------
1 minute into format ---- Formatting tracks, LBN # 32675
2 minutes into format ---- First check pass, writing LBN # 34867
3 minutes into format ---- First check pass, reading LBN # 9064
4 minutes into format ---- First check pass, reading LBN # 40715
5 minutes into format ---- Second check pass, writing LBN # 35003
6 minutes into format ---- Second check pass, reading LBN # 28271
8 minutes into format ---- Third check pass, writing LBN # 35003
9 minutes into format ---- Third check pass, reading LBN # 28271
Format Completed.
00002 Rev LBNs
00000 Bad RBNs
00000 Bad DBNs
00000 Bad XBNs
00002 retired
FCT was not used.
Drive 0 has been formatted successfully.
ZRQC EOP 1
0 TOTAL ERRS
DR>
150230
@1777773000G#
Testing in progress - Please wait
Memory Size is 4088 K Bytes
9 Step memory test
Step 1 2 3 4 5 6 7 8 9
Message 04 Entering Dialog mode
Commands are Help, Boot, List, Setup, Map and Test.
Type a command then press the RETURN key: BOO ZB1
Trying ZB1
Starting system from ZB1
RT-11SB (S) V05.07
.R MSCPCK
.SET DU CSR 172160
.DUMP/TERM/END:1 DU:
DU:
BLOCK NUMBER 000000
000/ 000004 000010 000020 000040 000100 000200 000400 001000 *...... .@.......*
020/ 002000 004000 010000 020000 040000 100001 000002 000004 *....... .@......*
040/ 000010 000020 000040 000100 000200 000400 001000 002000 *.... .@.........*
060/ 004000 010000 020000 040000 100001 000002 000004 000010 *..... .@........*
100/ 000020 000040 000100 000200 000400 001000 002000 004000 *.. .@...........*
120/ 010000 020000 040000 100001 000002 000004 000010 000020 *... .@..........*
140/ 000040 000100 000200 000400 001000 002000 004000 010000 * .@.............*
160/ 020000 040000 100001 000002 000004 000010 000020 000040 *. .@.......... .*
200/ 000100 000200 000400 001000 002000 004000 010000 020000 *@.............. *
220/ 040000 100001 000002 000004 000010 000020 000040 000100 *.@.......... .@.*
.......
.INI DU:
DU0:/Initialize; Are you sure? Y
Volume contains protected files; Are you sure? N
.DIR DU:
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
AKHBVP.ED2 16384 -BAD- AKHBVP.ED2 16384 -BAD-
...
.INI DU:
DU0:/Initialize; Are you sure? Y
Volume contains protected files; Are you sure? Y
.DIR DU:
0 Files, 0 Blocks
41492 Free blocks
.DAT 10-MAR-2021
.TIM 13:36
.TIM
13:36:45
.COP/SYS/VER SY:*.* DU:
Files copied:
SY:SWAP.SYS to DU:SWAP.SYS
SY:RT11SB.SYS to DU:RT11SB.SYS
SY:RT11FB.SYS to DU:RT11FB.SYS
SY:RK.SYS to DU:RK.SYS
SY:DL.SYS to DU:DL.SYS
SY:DU.SYS to DU:DU.SYS
SY:HX.SYS to DU:HX.SYS
SY:ZA.SYS to DU:ZA.SYS
SY:ZB.SYS to DU:ZB.SYS
SY:ZC.SYS to DU:ZC.SYS
SY:ZD.SYS to DU:ZD.SYS
SY:ZE.SYS to DU:ZE.SYS
SY:ZF.SYS to DU:ZF.SYS
SY:WQ.SYS to DU:WQ.SYS
SY:WS.SYS to DU:WS.SYS
SY:LD.SYS to DU:LD.SYS
SY:VM.SYS to DU:VM.SYS
SY:MU.SYS to DU:MU.SYS
SY:NL.SYS to DU:NL.SYS
SY:SL.SYS to DU:SL.SYS
SY:RT11XM.SYS to DU:RT11XM.SYS
SY:RT11XB.SYS to DU:RT11XB.SYS
SY:RT11ZM.SYS to DU:RT11ZM.SYS
SY:RT11ZB.SYS to DU:RT11ZB.SYS
SY:RKX.SYS to DU:RKX.SYS
SY:DLX.SYS to DU:DLX.SYS
SY:DUX.SYS to DU:DUX.SYS
SY:HXX.SYS to DU:HXX.SYS
SY:ZAX.SYS to DU:ZAX.SYS
SY:ZBX.SYS to DU:ZBX.SYS
SY:ZCX.SYS to DU:ZCX.SYS
SY:ZDX.SYS to DU:ZDX.SYS
SY:ZEX.SYS to DU:ZEX.SYS
SY:ZFX.SYS to DU:ZFX.SYS
SY:WQX.SYS to DU:WQX.SYS
SY:WSX.SYS to DU:WSX.SYS
SY:LDX.SYS to DU:LDX.SYS
SY:VMX.SYS to DU:VMX.SYS
SY:MUX.SYS to DU:MUX.SYS
SY:NLX.SYS to DU:NLX.SYS
SY:SLX.SYS to DU:SLX.SYS
SY:NQX.SYS to DU:NQX.SYS
SY:PIP.SAV to DU:PIP.SAV
SY:DUP.SAV to DU:DUP.SAV
SY:DIR.SAV to DU:DIR.SAV
SY:IND.SAV to DU:IND.SAV
SY:RESORC.SAV to DU:RESORC.SAV
SY:EDIT.SAV to DU:EDIT.SAV
SY:KED.SAV to DU:KED.SAV
SY:KEX.SAV to DU:KEX.SAV
SY:MACRO.SAV to DU:MACRO.SAV
SY:CREF.SAV to DU:CREF.SAV
SY:LINK.SAV to DU:LINK.SAV
SY:MONMRG.SAV to DU:MONMRG.SAV
SY:LIBR.SAV to DU:LIBR.SAV
SY:FILEX.SAV to DU:FILEX.SAV
SY:SRCCOM.SAV to DU:SRCCOM.SAV
SY:BINCOM.SAV to DU:BINCOM.SAV
SY:SLP.SAV to DU:SLP.SAV
SY:DUMP.SAV to DU:DUMP.SAV
SY:SIPP.SAV to DU:SIPP.SAV
SY:BUP.SAV to DU:BUP.SAV
SY:PAT.SAV to DU:PAT.SAV
SY:HELP.SAV to DU:HELP.SAV
SY:SYSMAC.SML to DU:SYSMAC.SML
SY:SYSLIB.OBJ to DU:SYSLIB.OBJ
SY:FORMAT.SAV to DU:FORMAT.SAV
SY:SETUP.SAV to DU:SETUP.SAV
SY:VTCOM.SAV to DU:VTCOM.SAV
SY:DATIME.SAV to DU:DATIME.SAV
SY:DATIME.MAC to DU:DATIME.MAC
SY:DATIME.COM to DU:DATIME.COM
SY:LET.SAV to DU:LET.SAV
SY:SPLIT.SAV to DU:SPLIT.SAV
SY:UCL.SAV to DU:UCL.SAV
SY:VBGEXE.SAV to DU:VBGEXE.SAV
SY:TERMID.SAV to DU:TERMID.SAV
SY:TRANSF.SAV to DU:TRANSF.SAV
SY:TRANSF.TSK to DU:TRANSF.TSK
SY:TRANSF.EXE to DU:TRANSF.EXE
SY:ODT.OBJ to DU:ODT.OBJ
SY:VDT.OBJ to DU:VDT.OBJ
SY:MDUP.SAV to DU:MDUP.SAV
SY:MBOOT.BOT to DU:MBOOT.BOT
SY:MBOT16.BOT to DU:MBOT16.BOT
SY:MSBOOT.BOT to DU:MSBOOT.BOT
SY:MDUP.AI to DU:MDUP.AI
SY:MDUP.MM to DU:MDUP.MM
SY:MDUP.MS to DU:MDUP.MS
SY:MDUP.MT to DU:MDUP.MT
SY:MDUP.MU to DU:MDUP.MU
SY:VERIFY.COM to DU:VERIFY.COM
SY:IVP.COM to DU:IVP.COM
SY:IVP.MAC to DU:IVP.MAC
SY:MTB.COM to DU:MTB.COM
SY:MSB.COM to DU:MSB.COM
SY:MUB.COM to DU:MUB.COM
SY:SB.MAC to DU:SB.MAC
SY:FB.MAC to DU:FB.MAC
SY:XM.MAC to DU:XM.MAC
SY:XB.MAC to DU:XB.MAC
SY:ZM.MAC to DU:ZM.MAC
SY:ZB.MAC to DU:ZB.MAC
SY:SYSTEM.MLB to DU:SYSTEM.MLB
SY:EDTL.MLB to DU:EDTL.MLB
SY:SYSGEN.COM to DU:SYSGEN.COM
SY:CONFIG.COM to DU:CONFIG.COM
SY:CONFIG.SAV to DU:CONFIG.SAV
SY:V5USER.TXT to DU:V5USER.TXT
SY:V5NOTE.TXT to DU:V5NOTE.TXT
SY:CUSTOM.TXT to DU:CUSTOM.TXT
SY:MSCPCK.SAV to DU:MSCPCK.SAV
SY:DBGSYM.SAV to DU:DBGSYM.SAV
SY:INDEX.SAV to DU:INDEX.SAV
SY:INDEXX.SAV to DU:INDEXX.SAV
SY:INDEXA.IMG to DU:INDEXA.IMG
SY:INDEXB.IMG to DU:INDEXB.IMG
SY:INDEX.IDX to DU:INDEX.IDX
SY:TECO.SAV to DU:TECO.SAV
SY:SGN02.CND to DU:SGN02.CND
SY:SGN02.ANS to DU:SGN02.ANS
SY:SGN02.BLD to DU:SGN02.BLD
SY:SGN02.MON to DU:SGN02.MON
SY:SGN02.DEV to DU:SGN02.DEV
SY:SGN02.TBL to DU:SGN02.TBL
SY:RT11SB.MAP to DU:RT11SB.MAP
SY:RT11FB.MAP to DU:RT11FB.MAP
SY:RT11XM.MAP to DU:RT11XM.MAP
SY:RT11XB.MAP to DU:RT11XB.MAP
SY:RT11ZM.MAP to DU:RT11ZM.MAP
SY:RT11ZB.MAP to DU:RT11ZB.MAP
SY:STRTSB.COM to DU:STRTSB.COM
SY:STRTFB.COM to DU:STRTFB.COM
SY:STRTXM.COM to DU:STRTXM.COM
SY:STRTXB.COM to DU:STRTXB.COM
SY:STRTZM.COM to DU:STRTZM.COM
SY:STRTZB.COM to DU:STRTZB.COM
SY:HELAY.SYS to DU:HELAY.SYS
SY:EM.SYS to DU:EM.SYS
SY:TSYB10.COM to DU:TSYB10.COM
SY:TSYNL.COM to DU:TSYNL.COM
.TIM
13:47:47
.DIR DU:
10-Mar-2021
SWAP .SYS 28P 31-Oct-1998 RT11SB.SYS 99P 02-Oct-2020
RT11FB.SYS 107P 02-Oct-2020 RK .SYS 3P 02-Oct-2020
DL .SYS 5P 02-Oct-2020 DU .SYS 24P 02-Oct-2020
HX .SYS 6P 12-Sep-2020 ZA .SYS 4P 05-Jul-2020
ZB .SYS 4P 05-Jul-2020 ZC .SYS 4P 05-Jul-2020
ZD .SYS 4P 05-Jul-2020 ZE .SYS 4P 05-Jul-2020
ZF .SYS 4P 05-Jul-2020 WQ .SYS 4P 05-Jul-2020
WS .SYS 4P 05-Jul-2020 LD .SYS 11P 02-Oct-2020
VM .SYS 3P 02-Oct-2020 MU .SYS 14P 02-Oct-2020
NL .SYS 2P 02-Oct-2020 SL .SYS 17P 31-Oct-1998
RT11XM.SYS 124P 02-Oct-2020 RT11XB.SYS 115P 02-Oct-2020
RT11ZM.SYS 127P 02-Oct-2020 RT11ZB.SYS 118P 02-Oct-2020
RKX .SYS 3P 02-Oct-2020 DLX .SYS 5P 02-Oct-2020
DUX .SYS 27P 02-Oct-2020 HXX .SYS 6P 12-Sep-2020
ZAX .SYS 4P 05-Jul-2020 ZBX .SYS 4P 05-Jul-2020
ZCX .SYS 4P 05-Jul-2020 ZDX .SYS 4P 05-Jul-2020
ZEX .SYS 4P 05-Jul-2020 ZFX .SYS 4P 05-Jul-2020
WQX .SYS 4P 05-Jul-2020 WSX .SYS 4P 05-Jul-2020
LDX .SYS 11P 02-Oct-2020 VMX .SYS 3P 02-Oct-2020
MUX .SYS 19P 02-Oct-2020 NLX .SYS 2P 02-Oct-2020
SLX .SYS 20P 31-Oct-1998 NQX .SYS 10P 02-Oct-2020
PIP .SAV 30P 31-Oct-1998 DUP .SAV 52P 31-Oct-1998
DIR .SAV 20P 31-Oct-1998 IND .SAV 58P 31-Oct-1998
RESORC.SAV 35P 31-Oct-1998 EDIT .SAV 19P 31-Oct-1998
KED .SAV 85P 31-Oct-1998 KEX .SAV 72P 31-Oct-1998
MACRO .SAV 63P 31-Oct-1998 CREF .SAV 6P 31-Oct-1998
LINK .SAV 59P 31-Oct-1998 MONMRG.SAV 14P 31-Oct-1998
LIBR .SAV 24P 31-Oct-1998 FILEX .SAV 22P 31-Oct-1998
SRCCOM.SAV 26P 31-Oct-1998 BINCOM.SAV 25P 31-Oct-1998
SLP .SAV 13P 31-Oct-1998 DUMP .SAV 10P 31-Oct-1998
SIPP .SAV 21P 31-Oct-1998 BUP .SAV 68P 31-Oct-1998
PAT .SAV 11P 31-Oct-1998 HELP .SAV 161P 31-Oct-1998
SYSMAC.SML 92P 31-Oct-1998 SYSLIB.OBJ 84P 31-Oct-1998
FORMAT.SAV 28P 31-Oct-1998 SETUP .SAV 43P 31-Oct-1998
VTCOM .SAV 24P 31-Oct-1998 DATIME.SAV 4P 31-Oct-1998
DATIME.MAC 23P 31-Oct-1998 DATIME.COM 3P 31-Oct-1998
LET .SAV 6P 31-Oct-1998 SPLIT .SAV 3P 31-Oct-1998
UCL .SAV 16P 31-Oct-1998 VBGEXE.SAV 18P 31-Oct-1998
TERMID.SAV 4P 31-Oct-1998 TRANSF.SAV 16P 31-Oct-1998
TRANSF.TSK 76P 31-Oct-1998 TRANSF.EXE 45P 31-Oct-1998
ODT .OBJ 8P 31-Oct-1998 VDT .OBJ 8P 31-Oct-1998
MDUP .SAV 22P 31-Oct-1998 MBOOT .BOT 1P 31-Oct-1998
MBOT16.BOT 1P 31-Oct-1998 MSBOOT.BOT 4P 31-Oct-1998
MDUP .AI 72P 31-Oct-1998 MDUP .MM 72P 31-Oct-1998
MDUP .MS 72P 31-Oct-1998 MDUP .MT 72P 31-Oct-1998
MDUP .MU 72P 31-Oct-1998 VERIFY.COM 2P 31-Oct-1998
IVP .COM 16P 31-Oct-1998 IVP .MAC 33P 31-Oct-1998
MTB .COM 16P 31-Oct-1998 MSB .COM 16P 31-Oct-1998
MUB .COM 16P 31-Oct-1998 SB .MAC 1P 31-Oct-1998
FB .MAC 1P 31-Oct-1998 XM .MAC 1P 31-Oct-1998
XB .MAC 1P 31-Oct-1998 ZM .MAC 1P 31-Oct-1998
ZB .MAC 1P 31-Oct-1998 SYSTEM.MLB 148P 31-Oct-1998
EDTL .MLB 11P 31-Oct-1998 SYSGEN.COM 286P 31-Oct-1998
CONFIG.COM 29P 31-Oct-1998 CONFIG.SAV 10P 31-Oct-1998
V5USER.TXT 2P 31-Oct-1998 V5NOTE.TXT 36P 31-Oct-1998
CUSTOM.TXT 14P 31-Oct-1998 MSCPCK.SAV 4P 31-Oct-1998
DBGSYM.SAV 10P 31-Oct-1998 INDEX .SAV 11P 31-Oct-1998
INDEXX.SAV 14P 31-Oct-1998 INDEXA.IMG 164P 31-Oct-1998
INDEXB.IMG 165P 31-Oct-1998 INDEX .IDX 7P 31-Oct-1998
TECO .SAV 50P 31-Oct-1998 SGN02 .CND 5P 02-Oct-2020
SGN02 .ANS 9P 02-Oct-2020 SGN02 .BLD 3P 02-Oct-2020
SGN02 .MON 10P 02-Oct-2020 SGN02 .DEV 6P 02-Oct-2020
SGN02 .TBL 5P 02-Oct-2020 RT11SB.MAP 34P 02-Oct-2020
RT11FB.MAP 35P 02-Oct-2020 RT11XM.MAP 38P 02-Oct-2020
RT11XB.MAP 36P 02-Oct-2020 RT11ZM.MAP 38P 02-Oct-2020
RT11ZB.MAP 36P 02-Oct-2020 STRTSB.COM 1P 31-Oct-1998
STRTFB.COM 5P 31-Oct-1998 STRTXM.COM 8P 31-Oct-1998
STRTXB.COM 5P 31-Oct-1998 STRTZM.COM 8P 31-Oct-1998
STRTZB.COM 5P 31-Oct-1998 HELAY .SYS 1 13-Jun-1988
EM .SYS 4 04-Mar-2012 TSYB10.COM 1 16-Oct-2020
TSYNL .COM 1 16-Oct-2020
141 Files, 4116 Blocks
37376 Free blocks
.COP/BOO DU:RT11ZM DU:
.BOO DU:
000002
@
- - - Добавлено - - -
Предположение о том, что проблема связана с нестандартным адресом подтвердилось
41560 блоков - итого скорость 236 кб/сКод:
Testing in progress - Please wait
Memory Size is 4088 K Bytes
9 Step memory test
Step 1 2 3 4 5 6 7 8 9
Message 04 Entering Dialog mode
Commands are Help, Boot, List, Setup, Map and Test.
Type a command then press the RETURN key: BOO DU0
Trying DU0
Starting system from DU0
RT-11ZM (S) V05.07
.TYPE V5USER.TXT
RT-11 V5.7
Installation of RT-11 Version 5.7 is complete and you are now running
RT-11 from your system volume.
Your system volume is your working volume if you have used the Automatic
Installation (AI) procedure. If you have installed RT-11 using that
procedure, Mentec recommends you verify the correct operation of your
system's software using the VERIFY verification procedure. You can only
perform VERIFY on the valid target (output) media you used for the AI
procedure. Run VERIFY before you run CONFIG. To run VERIFY, enter the
command:
IND VERIFY
You should read the file V5NOTE.TXT, which you can TYPE or PRINT. Also,
read the Introduction to RT-11, and the Installation Guide which
contain much of the information you need to use RT-11 Version 5.7.
.R MSCPCK
.SHO DEV
Device Status CSR Vector(s)
------ ------ --- ---------
RK Installed 177400 220
DL Not installed 174400 160
DU Resident 172150 154
HX Installed 177560 000
ZA Installed 161014 350
ZB Installed 161054 354
ZC Installed 161114 360
ZD Installed 161154 364
ZE Not installed 161214 370
ZF Not installed 161254 374
WQ Not installed 177134 204
WS Not installed 177134 204
LD Installed 000000 000
VM Installed 177572 000
MU Not installed 174500 260
NL Installed 000000 000
SL Installed 000000 000
NQ Installed 174440 120
.DIR
SWAP .SYS 28P 31-Oct-1998 RT11SB.SYS 99P 02-Oct-2020
RT11FB.SYS 107P 02-Oct-2020 RK .SYS 3P 02-Oct-2020
DL .SYS 5P 02-Oct-2020 DU .SYS 24P 02-Oct-2020
HX .SYS 6P 12-Sep-2020 ZA .SYS 4P 05-Jul-2020
ZB .SYS 4P 05-Jul-2020 ZC .SYS 4P 05-Jul-2020
ZD .SYS 4P 05-Jul-2020 ZE .SYS 4P 05-Jul-2020
ZF .SYS 4P 05-Jul-2020 WQ .SYS 4P 05-Jul-2020
WS .SYS 4P 05-Jul-2020 LD .SYS 11P 02-Oct-2020
VM .SYS 3P 02-Oct-2020 MU .SYS 14P 02-Oct-2020
NL .SYS 2P 02-Oct-2020 SL .SYS 17P 31-Oct-1998
RT11XM.SYS 124P 02-Oct-2020 RT11XB.SYS 115P 02-Oct-2020
RT11ZM.SYS 127P 02-Oct-2020 RT11ZB.SYS 118P 02-Oct-2020
RKX .SYS 3P 02-Oct-2020 DLX .SYS 5P 02-Oct-2020
DUX .SYS 27P 02-Oct-2020 HXX .SYS 6P 12-Sep-2020
ZAX .SYS 4P 05-Jul-2020 ZBX .SYS 4P 05-Jul-2020
ZCX .SYS 4P 05-Jul-2020 ZDX .SYS 4P 05-Jul-2020
ZEX .SYS 4P 05-Jul-2020 ZFX .SYS 4P 05-Jul-2020
WQX .SYS 4P 05-Jul-2020 WSX .SYS 4P 05-Jul-2020
LDX .SYS 11P 02-Oct-2020 VMX .SYS 3P 02-Oct-2020
MUX .SYS 19P 02-Oct-2020 NLX .SYS 2P 02-Oct-2020
SLX .SYS 20P 31-Oct-1998 NQX .SYS 10P 02-Oct-2020
PIP .SAV 30P 31-Oct-1998 DUP .SAV 52P 31-Oct-1998
DIR .SAV 20P 31-Oct-1998 IND .SAV 58P 31-Oct-1998
RESORC.SAV 35P 31-Oct-1998 EDIT .SAV 19P 31-Oct-1998
KED .SAV 85P 31-Oct-1998 KEX .SAV 72P 31-Oct-1998
MACRO .SAV 63P 31-Oct-1998 CREF .SAV 6P 31-Oct-1998
LINK .SAV 59P 31-Oct-1998 MONMRG.SAV 14P 31-Oct-1998
LIBR .SAV 24P 31-Oct-1998 FILEX .SAV 22P 31-Oct-1998
SRCCOM.SAV 26P 31-Oct-1998 BINCOM.SAV 25P 31-Oct-1998
SLP .SAV 13P 31-Oct-1998 DUMP .SAV 10P 31-Oct-1998
SIPP .SAV 21P 31-Oct-1998 BUP .SAV 68P 31-Oct-1998
PAT .SAV 11P 31-Oct-1998 HELP .SAV 161P 31-Oct-1998
SYSMAC.SML 92P 31-Oct-1998 SYSLIB.OBJ 84P 31-Oct-1998
FORMAT.SAV 28P 31-Oct-1998 SETUP .SAV 43P 31-Oct-1998
VTCOM .SAV 24P 31-Oct-1998 DATIME.SAV 4P 31-Oct-1998
DATIME.MAC 23P 31-Oct-1998 DATIME.COM 3P 31-Oct-1998
LET .SAV 6P 31-Oct-1998 SPLIT .SAV 3P 31-Oct-1998
UCL .SAV 16P 31-Oct-1998 VBGEXE.SAV 18P 31-Oct-1998
TERMID.SAV 4P 31-Oct-1998 TRANSF.SAV 16P 31-Oct-1998
TRANSF.TSK 76P 31-Oct-1998 TRANSF.EXE 45P 31-Oct-1998
ODT .OBJ 8P 31-Oct-1998 VDT .OBJ 8P 31-Oct-1998
MDUP .SAV 22P 31-Oct-1998 MBOOT .BOT 1P 31-Oct-1998
MBOT16.BOT 1P 31-Oct-1998 MSBOOT.BOT 4P 31-Oct-1998
MDUP .AI 72P 31-Oct-1998 MDUP .MM 72P 31-Oct-1998
MDUP .MS 72P 31-Oct-1998 MDUP .MT 72P 31-Oct-1998
MDUP .MU 72P 31-Oct-1998 VERIFY.COM 2P 31-Oct-1998
IVP .COM 16P 31-Oct-1998 IVP .MAC 33P 31-Oct-1998
MTB .COM 16P 31-Oct-1998 MSB .COM 16P 31-Oct-1998
MUB .COM 16P 31-Oct-1998 SB .MAC 1P 31-Oct-1998
FB .MAC 1P 31-Oct-1998 XM .MAC 1P 31-Oct-1998
XB .MAC 1P 31-Oct-1998 ZM .MAC 1P 31-Oct-1998
ZB .MAC 1P 31-Oct-1998 SYSTEM.MLB 148P 31-Oct-1998
EDTL .MLB 11P 31-Oct-1998 SYSGEN.COM 286P 31-Oct-1998
CONFIG.COM 29P 31-Oct-1998 CONFIG.SAV 10P 31-Oct-1998
V5USER.TXT 2P 31-Oct-1998 V5NOTE.TXT 36P 31-Oct-1998
CUSTOM.TXT 14P 31-Oct-1998 MSCPCK.SAV 4P 31-Oct-1998
DBGSYM.SAV 10P 31-Oct-1998 INDEX .SAV 11P 31-Oct-1998
INDEXX.SAV 14P 31-Oct-1998 INDEXA.IMG 164P 31-Oct-1998
INDEXB.IMG 165P 31-Oct-1998 INDEX .IDX 7P 31-Oct-1998
TECO .SAV 50P 31-Oct-1998 SGN02 .CND 5P 02-Oct-2020
SGN02 .ANS 9P 02-Oct-2020 SGN02 .BLD 3P 02-Oct-2020
SGN02 .MON 10P 02-Oct-2020 SGN02 .DEV 6P 02-Oct-2020
SGN02 .TBL 5P 02-Oct-2020 RT11SB.MAP 34P 02-Oct-2020
RT11FB.MAP 35P 02-Oct-2020 RT11XM.MAP 38P 02-Oct-2020
RT11XB.MAP 36P 02-Oct-2020 RT11ZM.MAP 38P 02-Oct-2020
RT11ZB.MAP 36P 02-Oct-2020 STRTSB.COM 1P 31-Oct-1998
STRTFB.COM 5P 31-Oct-1998 STRTXM.COM 8P 31-Oct-1998
STRTXB.COM 5P 31-Oct-1998 STRTZM.COM 8P 31-Oct-1998
STRTZB.COM 5P 31-Oct-1998 HELAY .SYS 1 13-Jun-1988
EM .SYS 4 04-Mar-2012 TSYB10.COM 1 16-Oct-2020
TSYNL .COM 1 16-Oct-2020
141 Files, 4116 Blocks
37376 Free blocks
.DAT 10-MAR-2021
.TIM 14:00
.@TSYNL
.TIME
14:00:10
.COPY/DEVICE/NOQUERY SY: NL:
.TIME
14:01:38
.
- - - Добавлено - - -
Ну, на этом интерес к RQDX3 исчерпан :)
Поскольку тут ко мне поступили... некие предложения... Уточняю - интерес исчерпан не значит, что она мне больше не нужна. Мысли на её счёт у меня есть, так что пока она останется у меня.
По ряду причин прогнал копирование CF-ки (точнее 65534 блоков) в NL:
KDJ11-B показала 537 кб/с
KDF-11B показала 207 кб/с
KDJ11-B у меня разогнанная при паспортном кварце на 18 МГц на плате стоит кварц на 24, то есть вместо 4.5 лимонов регистр-регистр – шарашит 6
Поскольку периодически мне хочется странного и поскольку для втыкания странного периодически оказывается, что корзинка не та...
После некоторых размышлений и покупок родилось НЕЧТО
Нечто слегка недоделанной (с одной из сторон) доделаю - перефотографирую :)